View Full Version : Fitting LCR splitter
Guinness
12-01-2007, 22:37
Fitting LCR splitter (Leon Cupra) to a seat Ibiza.
LCR splitter (part number =1ML805903) £20 aprox normally slightly less.
25mm self-drilling/tapping screws £3 B&Q
Black silicon Sealer £8 B&Q
Right well I thought as I had asked a lot of questions about fitting this part, it is probably an idea that I make a guide and help other people out too. Please excuse the pictures they aren’t too great but they give the general idea.
Firstly I will start by telling you to make sure you have plenty of room as this job can be fiddly, also an extra person would help here or masking tape. If you can raise the front of the car this would also help as it will give you more room under the car.
http://img125.imageshack.us/img125/9947/dsc00121ji4.jpg
• Start by cutting off the plastic Vs on in the middle of the splitter as these do not hook in as they are not on the Ibiza. You may also want to consider screwing the self tapping screws through the ridges on the splitter these are the best parts to use as they are slightly more reinforced, note putting the screws towards the lip on the splitter will help as it will pull the splitter in and keep a smaller gap than if you put it further back.
http://img125.imageshack.us/img125/9241/dsc00124yb0.jpg
• You will also want to cut some of the splitter off at either side don’t cut too much off, but cut enough off to allow more movement, you can always cut some more off later (I removed the hack saw blade and cut it just using that as not to damage the tyres).
• I next lined the splitter up, proper alignment is with the Vs in-between the metal posts central, that’s where mine are hope this makes some sense should when you have a look. Then your best bet is to masking tape the splitter up to the bumper, so that middle bit is attached pretty well, now comes the fiddly part if you have some strength and a decent size screw driver if you haven’t raised the car. The best thing to do here would be to drill I pilot hole, which I didn’t because I didn’t raise the car.
http://img123.imageshack.us/img123/5619/dsc00127jf2.jpg
• Here comes the screwing part I put the screws through the splitter and left them through with just the a little point through the edge before attempting to attach splitter to the bumper, there is also a personal preference point to note here, aligning how far back you want the splitter would be a good idea here as well before you put the screws in, mine was just a little bit off (about 1cm) the under lip where the bumper joins, putting it too far back makes the job rather pointless and 2 far forward looks crap. Once you have this sorted, screw in the middle 2 screws do this 1st and try to keep them even i.e. the same level so one side isn’t coming off at an angle as this will affect the whole splitter and put it out, i.e. 1 side out more than another.
• Next you want to work your way round both sides bending and screwing in the splitter to the size you want, once this is done you should cut off the excess around the wheel arches.
• Now with this finished it is probably a good idea as there will be some gaps to go around and fill them in with the black sealer, this matches well and just finishes it off perfect.
Couldnt get final pic as my cars in garage and couldnt get far enough back but take a look around looks cool, al take a pic when I get a chance outside.
Anyway there’s my guide hope it helps people, its not a hard mod but I think any help that people get before doing a mod is a good idea, even if it does just save a few mins.
Just to note you DONT remove the "V"s totally. U need them cut down a bit or u have nothing to screw into in the middle
Guinness
19-02-2007, 12:20
obviously you dont remove them out the plastic u just cut em down. O and I only used one screw for the middle to allow it to move with some freedom if it scraped on anything
Have ya got a pic? Cant understand how u put just one screw through the middle
If u put a screw through each of the "V"s its solid enough to take a hit.
Guinness
19-02-2007, 12:50
actually I think I took the middle one out, come to think of it will have a look later on. Didnt bother attaching it on the Vs cut them off and screwed it on around leaving the middle bit without any, so if it hit a curb or anythign like that it can move and hopefully wont rip anything off, being as that is the most likely part to hit
Ah rite. Woz just wondering cause took the screws outta the middle bit of mine to see if it held itself up and it jst dropped all saggy like. But hey to each his own
Guinness
19-02-2007, 13:31
ah I put lots of screws in and sealed it. so didnt sag
rallyslag3
26-03-2007, 23:27
Did you leave the non-colour coded part of the ibiza bumper? or remove it?
Guinness
30-04-2007, 23:46
leave it on
will this splitter fit 2003 pre face lift 1.9 130 tdi sport, or will it need to be modified. good pics though
Guinness
19-01-2008, 14:14
they always need to be modified matey, but yes it will fit with not much work
bbewekim
16-03-2008, 11:10
pics?
How much of the middle V's do you remove? just the bits that clip in or is it a certain measure?
cheers
Guinness
21-04-2008, 00:15
just a little bit. I usualy remove just a little bit less than the amount that would make the Vs level with the sides meaning the Vs are slightly but only a little bit higher than the sides of the splitter.
Damoegan
21-04-2008, 11:04
Didn't think you were going to do this mate :shrug: change of heart like?
Guinness
21-04-2008, 11:55
me?
bbewekim
10-07-2008, 16:33
just got my splitter today... anyone want to add some photos up? seems pritty straight forward i supose :d
bbewekim
12-07-2008, 21:56
Really easy to fit, i took to much off the middle so had barely anything to screw into so used a 2penny sized spacer. dodgy i know had the car on a trolley jack on oneside and it lifted the car enough to get underneith allround. aligned the splitter to the middle of the car, screwed it from the middle out, pritty easy to see where best to put the screws in, i think i used about 5 each side with the 2 in the middle.
Couldnt find my tripod but heres a rough picture, its such an improvement! (also accidently deleted half my damn photos so only have this under exposed one with flash on :() *world most awful photo on a 400d canon.
I am crying out to get my car lowered though the standard ride height sucks.
http://i88.photobucket.com/albums/k165/bbewekim/car_notripod11.jpg
can I just confirm that you've all drilled/screwed into the paintwork underneath the bumper?
And also, "mine was just a little bit off (about 1cm) the under lip where the bumper joins".
What under lip are you talking about? The only 'lip' under my bumper is a good few inches back, if I put the splitter about 1cm off that I wouldn't be able to see it!
Thank you
bbewekim
02-08-2008, 15:27
mine drilled into unpainted plastic part of the bumper at the bottom :). just place it where you think best :d but dont forget if you have it to far forward it may tilt up or look odd as it will be drilled on an angle.
hmmm, well I've done it, wasn't an unpainted part though.
I think it looks good myself, was sure I would mess it up but I like it!
http://img.photobucket.com/albums/v389/Devildude/IMG_4987.jpg
can i just ask did any ov u get a little gap wen u first screwd it in?
should i fill it with the black sealent.
btw i havent sealed it on yet but iv screwd it in and it lines up but its back off atm
a little help would be appreciated. thanks
I put it on my Ibiza, check it out:
http://img300.imageshack.us/img300/943/p8020314sd8.jpg (http://imageshack.us)
http://img300.imageshack.us/img300/943/p8020314sd8.ed68b6a120.jpg (http://g.imageshack.us/g.php?h=300&i=p8020314sd8.jpg)
NickyJam
20-08-2008, 10:15
can i just ask did any ov u get a little gap wen u first screwd it in?
should i fill it with the black sealent.
btw i havent sealed it on yet but iv screwd it in and it lines up but its back off atm
a little help would be appreciated. thanks
i didn't get any gaps but may be because i didn't make pilot holes...i had it held in place by a mate and made the hole with the screw...i also put 2 screws in each of the first 2 "V's" either side of the centre gap bit just to reinforce as bending it round puts a bit of strain on the middle
click on the link in my sig to check it out :)
mark_keeling52
23-08-2008, 14:40
Hi all,
I bought my LCR splitter last weekend and have come to fit it today (got my dad to help), but when holding it up against the bumper its shape is nowhere near the shape/radius of my bumper (05 ibiza cupra), especially in the middle where the splitter is straight and the bumper curves.
Am i right in thinking i need to bend it round at either end to pull it in-line with the radius and the front will not quite follow? (Bit of a newby to the modding scene so apologies if i seem a bit simple :-) )
Any help would be great.
Cheers
yes, it requires some bending... it's wise to do the fitting job with some assistance of someone else, so he can keep it into place while you fasten the screws.
Right! Iv come too getting some courage 2 fit my splitter ,As im scared i will mess up... Ok so looking at it theere are the 2 V things on ea middle side.. as said... I no i have too cut theys but if there cut 2 as low as u say theres nothing 2 drill? its hollow exsept a __ In it if i cut below that theres nothing 2 screw into! Do i cut this that low so i dont have anything or?? pics would be helpfull :O
Guinness
28-09-2008, 21:48
you need to cut the V part down until it is inline with the rest of the splitter then screw into the lower valance on the bumper.
you need to cut the V part down until it is inline with the rest of the splitter then screw into the lower valance on the bumper.
So u dont screw through where the v's were just around it? cos if i cut it that low theres nothing in the V 2 cut through :)
Very Helpful thread this!! Fitted mine a few months ago and looks spot on.
It is down to your own personal taste as to what sort of angel you want the splitter at, just make sure you have enough self tapping screws - i used 8 bought from homebase (little ones).
Another personal tatse is weather you want to use balck coloured sealent once fitted, i personally didn't use any.
jonisginger
30-11-2008, 20:31
That looks sweet! Cheers, am looking at fitting the splitter to my leon 1.6 s ...
more photos anyone??still unsure if i think it makes any difference
http://i290.photobucket.com/albums/ll265/bertrumscn/P1010140.jpg
jonisginger
15-12-2008, 23:47
Yeah it's good.
Poor quality photo but you get the idea :)
http://i156.photobucket.com/albums/t6/msjonesn/IMG_03841.jpg
want to fit my splitter but i cant raise the car the pilot holes i need to drill do these go in both the splitter and the front bumper or just the splitter? and if its just the splitter when i screw into the bumper wont it crack as its fibre glass? thanks
I drilled pilot holes only into the splitter. You position the splitter so the centres of the bumper and splitter are inline, then i worked from there.
I used 15 or 20mm 3.5mm Self tappers so pretty small, didnt do pilot holes in my bumper, as we were holding the splitter in location and fixing it there and then.
Hope this helps
want to fit my splitter but i cant raise the car the pilot holes i need to drill do these go in both the splitter and the front bumper or just the splitter? and if its just the splitter when i screw into the bumper wont it crack as its fibre glass? thanks
I didn't raise my car just did it on my drive with a good old screw driver (although my hands were in pain after i spent the few hours doing it).
It will be benefitial if you do pilot holes, the bumper wonn't crack if you use a small screw/drill piece on a slow setting!! :)
I didn't raise my car just did it on my drive with a good old screw driver (although my hands were in pain after i spent the few hours doing it).
It will be benefitial if you do pilot holes, the bumper wonn't crack if you use a small screw/drill piece on a slow setting!! :)
Similar with Nick_A, i didnt raise my car, I reversed my whole car up a kurb (using some ramps!), with just the front bumper hanging off the edge, gives abit more room :)
NickyJam
25-01-2009, 17:54
i wouldn't recommend pilot holes in the bumper as the self-tapping screws are designed to make the hole themselves for a tight fit...the splitter will be more secure this way :)
before:
http://i295.photobucket.com/albums/mm142/NickyJams/FR2-1.jpg
after:
http://i295.photobucket.com/albums/mm142/NickyJams/DSC02828.jpg
uzi_cupra
01-02-2009, 20:19
i bought the lcr splitter and attempted ot fit it today but my god was it a mess...i have the ibiza cupra tdi, and at the bottom of my bumper there is a bit which sticks out at both sides, so when trying to attach the splitter it was'nt sitting flush the whole way round...anyone else had the same problem with the cupre?I'll take pics in the morning and maybe that will explain it more...
i bought the lcr splitter and attempted ot fit it today but my god was it a mess...i have the ibiza cupra tdi, and at the bottom of my bumper there is a bit which sticks out at both sides, so when trying to attach the splitter it was'nt sitting flush the whole way round...anyone else had the same problem with the cupre?I'll take pics in the morning and maybe that will explain it more...
I made 4 spacers to even up the bottom of the splitter (2 on each side). I cut 4 equal pieces of copper pipe....roughly 2cm long, and sandwiched them in the gap by driving a screw through them. You can just about see two in this pic below
http://i226.photobucket.com/albums/dd36/Altech_2007/P1000051.jpg
Also make sure that you don't cut the two tabs in the middle of the splitter too much, otherwise it'll push up in the middle. I sprayed the spacers black too so they don't stand out. Hope that helps
this is something i put together for another guy who was confused about what to cut off.
http://i268.photobucket.com/albums/jj29/st10587/untitled-3.jpg
thats how i done it and the splitter fits nice and snug
uzi_cupra
03-02-2009, 23:35
I made 4 spacers to even up the bottom of the splitter (2 on each side). I cut 4 equal pieces of copper pipe....roughly 2cm long, and sandwiched them in the gap by driving a screw through them. You can just about see two in this pic below
Also make sure that you don't cut the two tabs in the middle of the splitter too much, otherwise it'll push up in the middle. I sprayed the spacers black too so they don't stand out. Hope that helps
i see...ok that makes a little more sense...so basically your saying fit the splitter on the bits that stick out and then fill the gaps in with a few spacers??
how hard is it to take the front bumper off? would you mind running through it, cheers :)
i see...ok that makes a little more sense...so basically your saying fit the splitter on the bits that stick out and then fill the gaps in with a few spacers??
how hard is it to take the front bumper off? would you mind running through it, cheers :)
Yes, use spacers to stop the splitter warping upwards in the middle.
It's better not to remove the bumper when fitting the splitter as the bumper can flex and would make fitting it quite difficult.
NickyJam
04-02-2009, 15:28
Yes, use spacers to stop the splitter warping upwards in the middle.
It's better not to remove the bumper when fitting the splitter as the bumper can flex and would make fitting it quite difficult.
just to make it a lil clearer...the spacers are only recommended for Cupra facelift bumper due to the small lips on either end
uzi_cupra
10-02-2009, 14:30
cheers guys, will post pics up of how i done it for others who are unsure...
im gunna give this a try this week it post pics if it works lol
tutorial helped really well, cheers, i think it completes the front end and really sets it off
kidinspace
11-08-2009, 13:55
Can anyone post a decent photo of what this looks like on a pre-facelift as I'm considering it but don't have the cash to replace the bumper.
Thanks,
.G.
Heres a couple of examples of mine when i had the pre-facelift bumper:-
http://i184.photobucket.com/albums/x34/CJFR/Car/020.jpg
http://i184.photobucket.com/albums/x34/CJFR/Car/6.jpg
P.S. I fitted mine about an inch back so it would sit lower.
If you want i can post a pic of the splitter on the prefacelift bumper while its off the car, as mine has been gathering dust for a good while. (i'll sell it if you're it interested, comes with the FR grills and fogs)
kevscupra
16-08-2009, 21:21
has any body got any pics of the splitter on a yellow mark 4 ibiza? cupra bumper?
just am thinking of getting 1 and am just wondering what it looks like
scoobsta1990
25-08-2009, 16:04
i know this might be a dumb question but im new to this forum where do you get the spiltter from?
kevscupra
25-08-2009, 21:47
i know this might be a dumb question but im new to this forum where do you get the spiltter from?
you can get the splitter off seat dealers and awesome gti sell them as well.
i know this might be a dumb question but im new to this forum where do you get the spiltter from?
Part Number's in the first post (in brackets, starts with 1M) Ring up your local dealer and get the to order you one. Go pick it up and watch their face drop in horror when they see you parl up in an Ibiza. I've fitted 2 now, so they're used to it :)
wedgie27
04-11-2009, 19:50
Awesome! I'm guna pop up to my local dealer tomorrow to order one.....they look amaziing. My mate has just fitted one on a fabia vRS and that looks mint too......but it looks better on the Ibiza!! :D
Few Q's for those in the know.. I've cut down the V's so they are flush now, bit messy but will sandpaper them to neaten it up.
Do I sit the middle 2 pieces flush up against the small lip that is at the back of the bumper? How much do I need to cut back off each piece near the wheels?
Anyone near Stoke fancy fitting it me?! :D:D
wedgie27
19-11-2009, 17:15
Few Q's for those in the know.. I've cut down the V's so they are flush now, bit messy but will sandpaper them to neaten it up.
Do I sit the middle 2 pieces flush up against the small lip that is at the back of the bumper? How much do I need to cut back off each piece near the wheels?
Anyone near Stoke fancy fitting it me?! :D:D
Sit it about 1cm back from the front of the bumper, too far back and it is pointless in fitting it as you wont see it.
The centre part in between the 2 Vs needs to be aligned with the centre of your bumper....I would recommend masking taping it on then standing back to judge it properly.
U shouldnt have to cut the ends off until you fully fitted it....I didnt anyway.
And it looks awesome!!
Hope this helps..........;)
thePHILosipher
23-01-2010, 22:39
hi guys, just a quick one, im goin to use self tappers, ive dug around in the odds and sods jar and come up with 8g x 25mm will they be to big to use??
cheers
CDJONES3495
07-02-2010, 21:23
This is a big help thanks people
mark_keeling52
23-02-2010, 18:54
I did finally get round to fitting mine so thanks for all the help. My Cupra is actually for sale now, so if youre interested message me for details (dont have enough posts to place an advert)
fletch2k00
01-03-2010, 15:32
deffo going to fit one of these splitters, make the front look so much better! [B)]
wedgie27
01-03-2010, 16:39
its awesome fletch
ayrshire_cupra
26-03-2010, 16:16
i think am going to attemp puttin one on next week
help, you know the v's, ive cut them down and i dont know where to screw thro them? it makes a V there's a hole where the v is. so where do i screw into them?
If you get a screw with a big enough head you can screw it up through the narrow part of the V to hold it in place.
wedgie27
11-04-2010, 19:54
Dom i didnt screw through the V's.......u will get away without screwing them
Looks good.
However, I fitted an LCR splitter to my last Golf R32 mk4 and I would personally say you have used way too many screw there. Should you ever hit anything that will make a totally mess of the bumper.
I ripped the splitter off my R32 and luckily I only put it on with 4 screws so it was great that it just broke straight off and caused no damage to the bumper. Any more screws and there would have been some serious damage to my bumper.
I can appreciate your car may not have clearance issues, in which case fairplay. Just dont think theres any need for that many fixings.
fitted it that day, but didn't end up using the silicone stuff as i didn't see where to really. has anyone got any pictures where they used it? because when i was going to take it back and get my £10quid back i must have miss placed my receipt and cant find it, so might aswell use it now ha
Why don't they just make one for the ibiza? It definitely sort the front of the car out! Need to order one soon from the stealers and start working on it if the weather allows!:lol:
Maverick08
29-09-2010, 16:04
got mine yesterday, hoping to get it done this evening or at some stage this week. so how much should you cut the two middle parts down to?
Depends on the bumper you're attaching it to Maverick. On the facelift bumper the middle bits need to be level with the sides if you know what i mean.
I got the sprit level out and marked it that way. Easy peasy.
Maverick08
29-09-2010, 17:01
so the top nib on them are completely removed? and then its cut down again from there to go level?
Aye, lay something long and flat across the 2 side bits across the middle of the splitter, mark it, give it a rough cut, test fit, bit of a sand down and then screw the beast on, cut sides off. Job done. lol Oh and forgot, take pic, post on readers rides.
My old bumper
http://i184.photobucket.com/albums/x34/CJFR/front1.jpg
barney501
18-11-2010, 15:48
Not the best picture in the world as from iphone, will get better once weather improves but just fitted mine and quite pleased with how it went
http://i101.photobucket.com/albums/m59/barney501/photo-27.jpg
from experience of fitting this to my FR, its all about making pilot holes in the splitter.
first leave about an inch of the centre 2 'V's remaining then drill a 5mm hole into the small tabs on the back of the splitter
when your putting it onto your car, you may not need to use all of the tabs to secure it
BUT make sure that you work your way round from the centre to each wheel arch and zigzag your way across the bumper to make sure it all aligns right, although this may have just been me being fussy about accuracy :D
also a recommendation, when you screw into the bumper, use 'penny washers' to make sure that the splitter has support if its knocked (so it wont rip off as easily)
i used 10 gauge 1.5" self tappers and they were a B**** to make bite so 8 gauge will probably be sufficient :D
oh and the amount you cut off at the wheel arch and what shape you do it to is up to you and your personal choice :)
hope this helps anyone who is worrying about doing it :D
mk4 cupra
13-04-2011, 11:30
looks good i like it i did the same modd to my old corsa c i had years ago it seems to be one on ethe biggest modds of this decade lol
Forde-99
27-04-2011, 18:39
Were can i get my hands on that splitter?
Were can i get my hands on that splitter?
From the stealers.
00Rupert
27-04-2011, 21:25
Were can i get my hands on that splitter?
About £25 from the stealers
grant2005ibiza
11-05-2011, 21:11
old thread I know. But where do I get the part from? Main dealer
cbr40017
16-06-2011, 13:52
Fitted mine over the weekend & have to say it defiantly finishes the front end off
http://i55.photobucket.com/albums/g137/paul1729/IMG_0265.jpg
rang my dealers today and these are £40 plus vat,also is it not better to remove the bumper to fit this as it must be alot easyer,also lads any idea on how long it takes to fit it
CasTiger7
26-03-2012, 11:43
Are there any other types of splitter that fit the FR bumper as I don't like the look of the LC on?
also is it not better to remove the bumper to fit this as it must be alot easyer,also lads any idea on how long it takes to fit it
No dude, if you take the bumper off it loses its ridgity/shape. It's a lot easier to do it with the bumper on the car.
Are there any other types of splitter that fit the FR bumper as I don't like the look of the LC on?
Facelift or pre?
CasTiger7
26-03-2012, 13:25
Facelift.
just bought it. i payed 29€ at local seat service. its a great bargain :)
kovzharov
03-09-2012, 09:18
Thanks for guide!
Need 15 post and I show you how it looks like on Aero Kit ;-)
veedub1981
15-09-2012, 12:31
the lcr splitter looks horrendous on the mk4 cupra bumper because of the shape of the bottom corners.
but they don't look to bad on the fr bumper because the bumpers flush around the the bottom.
i thought they were the same bumper.i didn't realize until closer inspection that there not.lucky i didnt go and buy a splitter.
Anyone want to fit one for me? :)
Dobbyboy
15-01-2013, 17:56
Anyone want to fit one for me? :)
Where you live mate? Done mine last week from the helpful guide here. Was easy, would recommend small cordless driver. Then you don't need to jack vehicle up.
No where near Sunderland ha. usually midlands / east Anglia.
Dobbyboy
17-01-2013, 07:05
No where near Sunderland ha. usually midlands / east Anglia.
Never mind ha
think this looks better with the center lugs still in place and not cut off.
Dobbyboy
20-01-2013, 19:26
think this looks better with the center lugs still in place and not cut off.
I agree I only trimmed mine down aproxx 15mm fits perfect.
I agree I only trimmed mine down aproxx 15mm fits perfect.
yh doesn't look anything without the lugs.
clouty86
20-01-2013, 22:18
has anyone ever color coded the splitter same at the rest of the car? wonder if it would look good. or would it just chip then look crap?
Dobbyboy
23-01-2013, 12:41
has anyone ever color coded the splitter same at the rest of the car? wonder if it would look good. or would it just chip then look crap?
I was tempted but with it slightly catching certain speeds humps and stone chips never bothered.
clouty86
23-01-2013, 18:19
I was tempted but with it slightly catching certain speeds humps and stone chips never bothered.
ya after i test fitted it think it will be better left black lol
Dobbyboy
23-01-2013, 19:45
ya after i test fitted it think it will be better left black lol
Think it sticks out in black a lot better, really sets the front end off.
Jaybeattie
23-01-2013, 20:35
How do these look on the prefacelift bumpers ?
Sent from my iPad using Tapatalk
Jaybeattie
23-01-2013, 20:52
Ignore my last post didn't realise the pics posted were on pre facelifts haha
Sent from my iPad using Tapatalk
Looks much better with the LCR splitter, next mod after lowering for sure!!
Whats recent price of one?
Dobbyboy
23-02-2013, 06:27
Looks much better with the LCR splitter, next mod after lowering for sure!!
Whats recent price of one?
Pretty sure I paid £24 inc vat from Newcastle tps about a month ago. That was trade price like not sure on what retail is. You can get them on eBay which a similar oe spec I believe.
AntiHeroUK
23-03-2013, 02:28
This is something I hope to get done this summer along with an endless list of others mods. But this one does make such a difference it's going to be sooner rather than later.
This is something I hope to get done this summer along with an endless list of others mods. But this one does make such a difference it's going to be sooner rather than later.
Overpriced from seat if you ask me, nearly £50 from my local dealer, I only payed £25 a few years ago when I put one on the corsa.
AntiHeroUK
23-03-2013, 15:43
Overpriced from seat if you ask me, nearly £50 from my local dealer, I only payed £25 a few years ago when I put one on the corsa.
I'll get a price from my local dealer and see what I think. It still smartens up the front of the car so it's still worth considering.
I'll get a price from my local dealer and see what I think. It still smartens up the front of the car so it's still worth considering.
Just picked one up for £30 new, took about 2hours to fit. Such a pain on the beezas lol
http://i796.photobucket.com/albums/yy244/n417han/D120F8A9-51C9-4DC3-9DD4-59BAFD8E1641-12494-00000EA454BBA8F4_zps6f840ff2.jpg (http://s796.photobucket.com/user/n417han/media/D120F8A9-51C9-4DC3-9DD4-59BAFD8E1641-12494-00000EA454BBA8F4_zps6f840ff2.jpg.html)