URGENT help needed please :-(

DGF264

Active Member
Jul 15, 2010
843
6
County Durham
Hey guys..

Basically I've bought and fitted a Piper cat back with zero silencers. So I'm running TB 3'' decat no silencers.. It's awful!!

Need (by tomorrow) if possible the length and width of the silencers you guys have fitted in the S bend pipe (the pipe where a Milltek would have the silencer fitted - & be resonated) Then tomorrow I can phone diff suppliers to have one next day delivered, to have it welded in on Wednesday (my next day off) As I can't drive it any longer like this

I appreciate it's a big ask of you all..and if I had access to ramps etc I'd measure the empty gap where a silencer should be lol.. But I thought it easier to get exact measurements off you guys of your silencers!

Please help!! Thanks in advance! ☺️


Sent from my iPhone using Tapatalk
 

oisin mc r

Active Member
Jul 20, 2010
93
0
Bury manchester
Hi,Iv bought the piper cat back with 1 silencer, just measured it there and it's exactly 12 inches long and 6 inches wide.
67bad8c733be5ddbd4fe2764f02a7765.jpg



Sent from my iPhone using Tapatalk
 

DGF264

Active Member
Jul 15, 2010
843
6
County Durham
Nice one thanks Oisin! anyone with a Milltek or BCS? (As I think they have a bigger box fitted!)


Sent from my iPhone using Tapatalk
 

oisin mc r

Active Member
Jul 20, 2010
93
0
Bury manchester
No problem mate.i was going to go for the one you have but then I thought it would be far too loud so went for 1 silencer.just need to get all fitted now


Sent from my iPhone using Tapatalk
 

DGF264

Active Member
Jul 15, 2010
843
6
County Durham
Haha good choice! I've just emailed the place I bought it from actually hoping they can contact piper and maybe I can buy just the silencer! Awesome exhaust etc, just too loud lol!


Sent from my iPhone using Tapatalk
 

oisin mc r

Active Member
Jul 20, 2010
93
0
Bury manchester
Yeah iv had an ep3 type r with a hks hi power exhaust and it is basically a straight pipe the back box is that small,ears were always ringing when I stopped car so didn't want that again lol I'm sure they would be able to sell you a silencer on its own but they might charge you a lot for it.


Sent from my iPhone using Tapatalk
 

DGF264

Active Member
Jul 15, 2010
843
6
County Durham
I didn't anticipate the 'loud sound' being so loud. And as I didn't know how it would sound before hand, I obviously had no way of knowing did I lol. Hence I'm trying to do something about it now


Sent from my iPhone using Tapatalk
 

DGF264

Active Member
Jul 15, 2010
843
6
County Durham
Hey Oisin.. I actually had 2 fitted in the end lol!! A JETEX one on the S bend pipe..but it still wasn't quite right..so I went to powerflow and had another one put in (where the cat usually is) So now in fairness it's a totally custom Piper/Jetex/Powerflow exhaust and it sounds awesome lol U got yours on yet?


Sent from my iPhone using Tapatalk
 

oisin mc r

Active Member
Jul 20, 2010
93
0
Bury manchester
No iv got mine sitting in the spare room still lol got engaged at Xmas so had to buy a ring for the misses and work has been a bit slow getting started again with the weather so need to wait to get some money back in before I can justify splashing out on more parts as I need the rear diffuser to fit the exhaust.. It's looking like it could take me a while now to get the car the way I want it


Sent from my iPhone using Tapatalk
 
Progressive Parts, performance parts and tuning specialists