Help needed - need part no. for cupra R centre console gauge holder!

[davidol]

as above guys, i need the seat part no. for the mk3 ibiza cupra R center console gauge holder as i'd like to fit my own 2xaftermarket 52mm gauges. Will the holder come with all the required fixings etc?

 

[acidstrato]

theres no extra fittings, the panel just pops into place


iv posted the p/n no end of times, but i dont have it at hand so

 

[acidstrato]

infact just to point out...i didnt even need to search...i just looked down the page of topics!!!!

theres ur part number!

i paid bout 8quid + VAT from dealer

not sure bout part number but on the back it says

6K0 863 263

think thatsa part num

 

[Buster247]

Picked mine up today 6K086326301C is the part number for a satin black one and it cost £10.58 inc vat.

There You Go,
Chris

 

[Funkyfin2000]

theres no extra fittings, the panel just pops into place


iv posted the p/n no end of times, but i dont have it at hand so

Ahhh seems like i found the question....

confirmed... the cupra r guage pod just pops into place

 

[B3NPM_Cupra]

Cupra R centre console Gauge pod: 6K0 863 263

 

[Forbez]

Parts list at the top of the forum!

And do you reckon you'd have to mod something that is standard on a car with the same interior??




Sheesh!

 

[Funkyfin2000]

Cupra R centre console Gauge pod: 6K0 863 263

why is some quoting with the extra part then?

6K0 863 263 01C

any how.... i read about someone screwing some xtra part in!

only a question!

 

[pdcupra]

i had this problem when ordering mine a few days back - the parts bloke said straight away, "its not come up, i should think it has 01C on the end" and it came straight up! Pretty sure its just clip in mate, although some mention you have to take some of the lower centre console apart?

 

[Funkyfin2000]

cheers dude, im gonna order up today with that part number...

pdcupra - what are you doing then? have you got urs yet?

 

[PhilW]

I dont get this thing, mine doesnt seem to want to sit properly if i 'pop it in place' Or am i just being stupid?

 

[Forbez]

Option 2 phil!

 

[Funkyfin2000]

Option 2 phil!

Parts list at the top of the forum!

And do you reckon you'd have to mod something that is standard on a car with the same interior??




Sheesh!

-----------------------------


So u do have to mod something then!

 

[Forbez]

 

[Bogwoppit]

Phil,
you can fasten it at the top as there are holes to do so. Mine wouldn't sit in properly until I cut away the floor of the cubby that it covers, the gauges were clashing.

 

[Funkyfin2000]

hmmm i dno't really want to cut any of my dash!

 

[PhilW]

I'll fasten it at the top first, and if it doesnt sit properly i'll just modify the holder itself and not the cubby.

Cheers tho.

 

[Bogwoppit]

Are you ever likely to remove the dials if you sell the car? If not the clearance hole you created will never be seen.

 

[Funkyfin2000]

just prefer not to ruin the dash and keep original.....i presume quite a few people have dnoe it without ruining the dash?

 

[Bogwoppit]

Can't answer that, but if you use Autometer phantom dials as I did, the console gauge holder will not fit correctly without clearance.
You could always fit some big spacer rings and space the gauges out from the console.