Helo o all,
I am asking for your help for solving this problems I currenly have.
I made 2 changes to my car and now I have new errors for which I cannot find solutions on the net.
1. I added led footwell lights so this error is permanent:
0531 - Footwell Illumination
B11FF 01 [009] - Electrical Failure
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 25
Mileage: 204566 km
Date: 2024.01.21
Time: 15:07:41
Terminal 15 status: On
Terminal 50 status: OFF
CAN-Bus_aktiv: On
Status Bremslichtschalter (HW): OFF
Status Bremslichtschalter (CAN): OFF
OFF: operated
Position lamps: Not operated
Automatic high beam assist: Not operated
Low beam: Not operated
Parking light left: Not operated
Parking light right: Not operated
last_wakeup: no cause for fault protection
Voltage: 11.7 V
Outside temperature: -2.5 C
2. I added reversing camera
131689 - Rear View Camera System Control Module
U104C 00 [008] - No communication
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 65
Mileage: 204572 km
Date: 2024.01.21
Time: 15:20:43
Terminal 30 power supply: 13.2 V
Terminal 15: OFF
10489856 - No Basic Setting
B2010 00 [009] - -
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 5
Fault Frequency: 1
Reset counter: 25
Mileage: 204566 km
Date: 2000.00.00
Time: 00:00:00
OFF
13705478 - Databus
U1121 00 [009] - Missing Message
[New feature! Extended UDS fault detail is only supported by current gen. interfaces]
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 25
Mileage: 204572 km
Date: 2024.01.21
Time: 15:20:50
passive
I know that for 'No basic setting' i need ODIS, but for the other error I cannot find solutions on the net.
I am asking for your help for solving this problems I currenly have.
I made 2 changes to my car and now I have new errors for which I cannot find solutions on the net.
1. I added led footwell lights so this error is permanent:
0531 - Footwell Illumination
B11FF 01 [009] - Electrical Failure
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 25
Mileage: 204566 km
Date: 2024.01.21
Time: 15:07:41
Terminal 15 status: On
Terminal 50 status: OFF
CAN-Bus_aktiv: On
Status Bremslichtschalter (HW): OFF
Status Bremslichtschalter (CAN): OFF
OFF: operated
Position lamps: Not operated
Automatic high beam assist: Not operated
Low beam: Not operated
Parking light left: Not operated
Parking light right: Not operated
last_wakeup: no cause for fault protection
Voltage: 11.7 V
Outside temperature: -2.5 C
2. I added reversing camera
131689 - Rear View Camera System Control Module
U104C 00 [008] - No communication
Intermittent - Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 2
Fault Frequency: 1
Reset counter: 65
Mileage: 204572 km
Date: 2024.01.21
Time: 15:20:43
Terminal 30 power supply: 13.2 V
Terminal 15: OFF
10489856 - No Basic Setting
B2010 00 [009] - -
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 5
Fault Frequency: 1
Reset counter: 25
Mileage: 204566 km
Date: 2000.00.00
Time: 00:00:00
OFF
13705478 - Databus
U1121 00 [009] - Missing Message
[New feature! Extended UDS fault detail is only supported by current gen. interfaces]
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 6
Fault Frequency: 1
Reset counter: 25
Mileage: 204572 km
Date: 2024.01.21
Time: 15:20:50
passive
I know that for 'No basic setting' i need ODIS, but for the other error I cannot find solutions on the net.