-
Hi Guest we, are working on an upgrade to the forum this week, meaning the service may be unreliable at times and there will be some planned downtime at some point. Stay updated on this thread.
-
Guest, 🚨New Stock alert: Premium CUPRA valve caps now available in the store 👉 Order now from the merchandise store
BT Questions, Can a BT set-up run of a 'tweaked' Stage 2 map?
- Thread starter Mo Arif
- Start date
How much power are you looking for? Surely you don't have far to go before you will be bending rods?
But then again, I've read standard internals are good for more, 320Bhp ish, I'd be happy with 300bHP
There's one lad here running around 320 on standard internals, clutch, gearbox.
AUQ Engine has decent pistons
AUQ Engine has decent pistons
Pyro
Guest
Pretty sure pats running 320ftlb on stanfmdard internals 
but could be wrong think you need all new mapping tho mo as you'll be changing injectors maf etc and adjusting boost So pretty sure it's a new map if your only looking for 300bhp then why not wait untill bill has a price for the new hybrid?
but could be wrong think you need all new mapping tho mo as you'll be changing injectors maf etc and adjusting boost So pretty sure it's a new map if your only looking for 300bhp then why not wait untill bill has a price for the new hybrid?
Its not the pistons i would be worried about. I have heard of people bending non forged rods at much less power. But i don't know the full ins and outs of there scenarios, may have been poorly maintained, or set up incorrectly.
This guy:
http://www.seatcupra.net/forums/member.php?u=9784
Username: 'traumapat'
His running good power all on standard internals
I've read the horror stories of bent rods, but that's with people aggressively launching their car every chance they get, and using WOT box's, neither interests me.
http://www.seatcupra.net/forums/member.php?u=9784
Username: 'traumapat'
His running good power all on standard internals
I've read the horror stories of bent rods, but that's with people aggressively launching their car every chance they get, and using WOT box's, neither interests me.
Pyro
Guest
If the map was to aggressive and your planted it a low revs you will bend a rod but at the higher revs it should be ok I've seen LCR rods bend on a little over 320 ftlb but I suppose its car dependent as I said I fairly sure pats LC is on standard internals with 320 bhp and 320 ftlb it's got and IHI BT set up
Pretty sure pats running 320ftlb on stanfmdard internals
K03S Hybrid ? I thought they topped out at 260-280, I've seen the JBS set-up, it looks and sounds good on paper, but I'm not too sure about it.
What sort of Bhp you going for Sam?
Pyro
Guest
Hmmmmm.........
I've read it all from start to finish, it sounds good but it's not really complete tried and tested is it, also no indication of price(s) for supplied and fitted or provided and fitted.
I've read it all from start to finish, it sounds good but it's not really complete tried and tested is it, also no indication of price(s) for supplied and fitted or provided and fitted.
its working fine so far
Prices prices prices
Packages packages packages
Need to start saving
why? some LC have the same 20mm wrist pin like the LCR, not all have the small 19mm wrist pin.
so if the LC is one with 20mm wrist pin the only diffense is the LCR is running 9.3:1 compression and the LC is running 9.5:1
Pyro
Guest
Lol I'm waiting for a price to all we know is it will be cheaper than BT but more exspensive than normal hybrids
all we know is it will be cheaper than BT but more exspensive than normal hybrids
Lol I'm waiting for a price to
Yeah but it has to be cheaper then a BT by a reasonable amount, if it's like 500-1K difference then it's probably a better idea to go BT.
We need prices!
Similar threads
