logging

Any care to comment on the logs? Group A: '003 Group B: '020 Idle speed Air mass in Throt Angle Ignit Angle Idle Stabilization Idle Stabilization Idle Stabilization Idle Stabilization TIME 700-820 rpm 2.0-4.5 g/s 0.2-4.0% 0-12 BTDC TIME STAMP /min g/s % °ATDC STAMP CF CF...

Was out logging my k04-023 golf gti at lunchtime to find out if i still had an overboosting problem. Tested with the n75 unplugged electrically and car was making 7psi which shows me the actuator and wastegate seems fine.. N75 plugged back in, car was requesting and making 1.3 bar which...

Hi all Seat Ibiza Cupra 2001 X reg 1.8 20v T mk3 Have now finished removing my SAI and have a resistor in the N112 plug, no fault codes at all now Thought I'd do some logs to see how things are. Outside temp was 18 degrees, runs done in 3rd and 4th gear, mostly 3rd! Car was...

Hi all, Been tinkering trying to fix a few faults relating to a boost leak (which does seem to have gone now) but thought I'd like to do a check on several main engine related parts but still getting to grips with this all so was wondering what are the good VAG COM logs to run and in...

Hi, Im not to good with the logging side of things so was just wondering if there is any logs i can do to check my car as im running way to less bhp and torque so could do with checking thins to see if they are up to scratch... or it may be my map... time will tell.. thanks

Can anyone tell me what channels should i log to check actual and requested boost? What other channels should i check as well to check if everything is running fine ? Thank you very much for help.

found this from Saul under the stickies - thanks http://www.seatcupra.net/users/saul/files/VAG_dbw_blocks.xls going to be doing some logging. Can you please confirm what blocks I should be using as I dont think the car is running right...feels like there is a leak some where or it is just...

How do I go about doing the data logging on vag-com to get the performance figures like bhp, torque and boost pressure?? Where do I go and what do I need to do??

Even if your MAF is knackered should you still get any (g/s) reading when logging in the Air Mass Flow column ?? :confused:

I'm a bit new with this vag-com stuff, I've done the simple things like change alarm chirps, etc.. I've done a seach and cannot find any advice on how to actually do the logging, so if poss i'd like a blow by blow on how to do it properly, as i've recently fitted a smoothed air box and larger...

hello!! just fitted a TIP and i've been out for a play...sounds loads better and spool up seems really quick...also fitted a new MAF as old one was dead!!! Is there any chance someone could plot these results on exel as i don't have exel and if i did i wouldn't know what i was doing with the...

can anyone tell me what i should be looking for ('ideal values') for logging groups 115 and 118 actual vs requested? ive been looking at my log sheet and have got between 2000-2400 mBAR , i did a calculation on google and thats like 30-34 PSI? im confused because my boost gauge is...

When logging lambda what am i actually looking out for, readings wise? On a 4th gear run..... 3600...0.977,1.000 4040...0.961,1.000 4480...0.938,0.930 4880...0.875,0.891 5240...0.836,0.860 5600...0.844,0.852 5920...0.860,0.852 6240...0.821,0.852 6480...0.805,0.852...

Ive had a look and see bost logging is block 115 but where in vag-com is this? i cant find it, im running version 311.2-n cheers

think i got boost leak where when i foot down i could here the turbo but the car not launching right. the bost gauge works but there is no pull when you ground the foot. i got vag .com any1 could tell me how to monitor the boost? what readins are normal? (leon 1.8T 180bhp - vipper...

Need help logging a Frontera FMIC that i just installed please and maybe even check my maf is running ok. Not far from Junction 15/16 M4, Don't mind traveling a little distance. Cheers jay

what modules do i log to find out the follwing; a)if my maf is fubard b)if my lambda is fubard c)i have a vacum leak(if this is possibe to log) d)exhaust gas temps also for each of the above what am i looking for when i look at the results i already no MAF is g/s isnt and for a revo'd...

hi new to vag com can someone tell me which blocks i need to log for intake temps and what blocks would be useful to log any help would be great:D

just been out for some testing on my private air strip and got some iffy results how much control does traction control actually have once you've switched it off..i dont believe its fully off but abit shocked if what im hearing/feeling at full wack is the tcs cutting in? floor it, car pulls...

hi i want to see what my temp sensors doing during start up. what blocks do i need to log please