1.8t underpowered! vcds log inside,help?

[spanner87]

Hi guys, initial thoughts were maf which was replaced, lambda readouts look within limits? the boost actual and specified is what throws me off

car is a pre facelift mk1 cupra with the auq 180 engine

spec is :

silicone tip (new)
stage 1 map
decat and 3inch dp
full exhaust system
710n d.v (good condition)
n75e (new)
pipercross induction kit (new)
ko3s turbo
new genuine maf


as far as i know,no boost leaks present
boost spikes to 20psi and holds boost if in e.g. 6th gear under load
otherwise it will spike to 20 then tail off and hold around 9 as the revs climb

has a code on engine block for 17704 error in mapped coolant system which i have a fresh thermostat + CTS sat here waiting to go in (unrelated??)

i have the money to get this sorted but would rather avoid the stealers and get a more confirmed diagnosis.

here are logs

https://docs.google.com/spreadsheet/pub?key=0AuF2Qzt9PQgUdDlqMFZNbnBYc3JERmJEVUZUZTBEZkE&output=html

thanks for your time

any help would be greatly appreciated


https://docs.google.com/spreadsheet/pub?key=0AuF2Qzt9PQgUdDlqMFZNbnBYc3JERmJEVUZUZTBEZkE&output=ods

 

[brad_barker12]

although im not very clued up on vagcom diagnostics the specified boost and actual boost differ. I would say boost leak. are you certain there are no boost leaks at all?

 

[Azza_]

148 g/s is standard for a 1.8t auq ive pulled 152 g/s in my unmapped auq

and yeah actual vers requested boost is WAY off points to boost leak!

a mapped car im sure peaks at 20psi and holds 16/18?

9 is very low

 

[Dmoe]

can i just ask quick question ive only got VCDS lite as to expensive for Full version but which blocks should i record to make sure everything running ok on my car.

 

[spanner87]

thanks for the replys guy,im going to replace every hose and fit a front mount to renew all the intercooler pipework,just hoping its not a faulty wastegate or something along those lines,it literally holds 8psi at redline :/

would the g/s reading be influenced by the lack of boost?
dmoe try logging blocks 003 031 032 114 and 115
start in 2nd or 3rd at 2500rpm and go full throttle to redline

interesting you say about the stock g/s readings bud,indicated im running wayyyyy under power then

bloody cars, do regular car garages hae smoke testing equipment or am i best off making my own boost leak tester?

 

[Dmoe]

Just run a log my mass airflow peeked at 204g/s is that what I should expect from stage 1?

 

[matty85]

That would make 250bhp so maybe you have a crap maf

 

[Dmoe]

Would it be the fact I got standard airbox?

 

[Azza_]

thanks for the replys guy,im going to replace every hose and fit a front mount to renew all the intercooler pipework,just hoping its not a faulty wastegate or something along those lines,it literally holds 8psi at redline :/

would the g/s reading be influenced by the lack of boost?
dmoe try logging blocks 003 031 032 114 and 115
start in 2nd or 3rd at 2500rpm and go full throttle to redline

interesting you say about the stock g/s readings bud,indicated im running wayyyyy under power then

bloody cars, do regular car garages hae smoke testing equipment or am i best off making my own boost leak tester?

the g/s is what the air is travelling past the MAF, you divide your g/s by 0.8 i think which gives your a rough bhp its no exact but give you a good idea

before going to a garage just give all your hoses a good once over, but first get the engine temp situation sorted i wouldnt expect it to make much difference but itll eliminate that

the thermostat is a pig to get at and its worth shifting the alternator first to give much more room!

Just run a log my mass airflow peeked at 204g/s is that what I should expect from stage 1?

what car do you have? a cupra? or an R as stated 204gs roughly 250bhp

 

[Dmoe]

what car do you have? a cupra? or an R as stated 204gs roughly 250bhp

It's a Cupra R Revo stage 1

 

[Azza_]

It's a Cupra R Revo stage 1

revo quote 265 bhp from stage 1 but its all hitty missy depends on car etc so sounds like a good figure

could be the airbox restricting air perhaps?

 

[spanner87]

thanks azza,i will be doing as much of the work as i possibly can,the last turbo car i owned was a starlet gt turbo so everything was a lot more basic and mechanically controlled rather than all this new technology lol,learning fast though.
looks like a got a busy weekend ahead.

would a n249 delete be beneficial to minimise hoses that could split in the future?

 

[Azza_]

thanks azza,i will be doing as much of the work as i possibly can,the last turbo car i owned was a starlet gt turbo so everything was a lot more basic and mechanically controlled rather than all this new technology lol,learning fast though.
looks like a got a busy weekend ahead.

would a n249 delete be beneficial to minimise hoses that could split in the future?

yeah do it i say less pipes is always good, its not hard just looks complicated

 

[Dmoe]

VCDS Run

Just a little snipet of my run i notce the temp does drop on my car when going for it a little but would that not be down to airflow or dodgey switch.


http://www.flickr.com/photos/dgoodchild/8614002279/

 

[brad_barker12]

where abouts are you guys from as ive got a problem with my car going into limp and really need it hooked up to vagcom to do some data logging

 

[spanner87]

im not sure about the coolant temps mate tbh.

brad im from west sussex,nr portsmouth,bit far for you i think lol

 

[brad_barker12]

yehh just a tad mate lol, shame.

how did you get vagcom if u don't mind me asking as I could really do with getting it lol

 

[spanner87]

I managed to get it on ebay believe it or not,I think it was £45 quid for genuine cable and registered copy on cd,think I just got very lucky lol

 

[cleverspoon]

You can download vcds lite for free, then buy a usb obd2 lead off ebay (i paid £13) then hey presto. If you want to fully register vcds you can for $99.

 

[Mattyboy1]

Where do you download the vcds lite from