Pillar Pod Where to buy?

[dtmwelburn]

Looking at getting a single pillar pod for boost gauge, but looking at universal ones theyll need too much fiddling etc to make them sit nice, does anywhere sell them shaped to the leon pillar? at a decent price?
Dan

 

[richybigman]

http://www.nomadracing.com/catalog/index.php?cPath=56&osCsid=fef5644f42f1009b4fb1bec96abb0244

 

[richybigman]

Only place i know and is what most paeople use on here as far as i know

 

[dtmwelburn]

I got one from www.body-kit.co.uk not too bad just under 30quid for carbon one to fit straight to leon APillar, then paid £24 for a plasma gauge

 

[richybigman]

I think he's after the whole 'a' pillar with gauge mounts built in?

 

[s_purs]

There is a whole other thread going about this at the moment....

http://www.seatcupra.net/forums/showthread.php?t=127039&page=2

 

[seatcupramad23]

sorry hi jack thread look to put 3 gauges into middle dash vents , does any do pods for it or will it be fibre glass custom set up ?

 

[rjpwalker]

Got mine from nomad. Nice guys on the phone and it's pretty good. Needs tweaking to fit but I give it 8/10

 

[Deleted member 12147]

sorry hi jack thread look to put 3 gauges into middle dash vents , does any do pods for it or will it be fibre glass custom set up ?

A company used to sell these on the German eBay can't remember how much they were tho.

 

[SalSheikh]

sorry hi jack thread look to put 3 gauges into middle dash vents , does any do pods for it or will it be fibre glass custom set up ?

one i built myself.

 

[s_purs]

That looks pretty awesome. Id love to do that to replace the cup holder and then move the warning and heater buttons, and keep the vents. If I knew how to do all of that I would do that!

 

[seatcupramad23]

one i built myself.

spanking , how much would charge to build one for mwah ?

 

[s_purs]

id change the far left one to be a universal phone holder. would be awesome to have that secured in at the same time. then have boost and oil temperature as the other two.

but then have them below the vents (as said above) as I hate that panel of the centre console. The surround is such a horrible colour, I never use the drinks holder, the warning light and heated screen buttons are too big for the amount of times I use it, and the airbag light is pointless

 

[s_purs]

If I could get that made to a good finish, and if I could find someone (or if my friend could) to fit it/move the buttons then Id pay for that for sure!


Edit: Didnt realise they were quite easy to buy (but not as nice looking as yours! http://cgi.ebay.co.uk/TAPE-RADIO-ST...495008&cguid=c92a805612a0a0e2042291c2fecd723a

Would be tempted to fit that, but still would need to know how to wire them in, and move the two buttons to under the ash tray

 

[Mo Arif]

Nomad is over priced imo, piece of moulded plastic which still has to be screwed in

I'd rather pay £10 for a generic one

 

[SalSheikh]

Edit: Didnt realise they were quite easy to buy (but not as nice looking as yours! http://cgi.ebay.co.uk/TAPE-RADIO-ST...495008&cguid=c92a805612a0a0e2042291c2fecd723a

thats a standard DIN size, the trim at the top to which you refer to is longer so you would have fill in the gaps.

 

[LEE69]

Edit: Didnt realise they were quite easy to buy (but not as nice looking as yours! http://cgi.ebay.co.uk/TAPE-RADIO-ST...495008&cguid=c92a805612a0a0e2042291c2fecd723a

That would be a good base to start from though.

 

[s_purs]

thats a standard DIN size, the trim at the top to which you refer to is longer so you would have fill in the gaps.

Cheers for that, I didnt realise that wasnt the whole width. Is there a DIN size that fits the whole Leon center console?