Cupra Petrol Remap With decat?

[cupra.al]

i have a blueflame resonated turbo back with 100cell cat and it sounds pretty much the same as the milltek version.

 

[Scott-o]

Just get it done by who done mine, 200 quid and he will enable launch control too. If you go decat I'd get a resonator in the system as it's abit more sly then.

Plus I have my mot sorted and, touch wood, police seem allot sounder up here than down south

 

[wazza16]

would it be really loud non-res? who done your map scott?

 

[Cos]

I've got a decat non res system mate.
Tbh, it's not ridiculously loud. Obviously idle is quite heavy, and when you floor it the thunderstorm really cracks haha, but driving at 30 in 4th/5th is fairly civilised

 

[Scott-o]

would it be really loud non-res? who done your map scott?

Big fish tuning, located in Stokesley, North East. Won't be too bad a journey, especially compared to going down the midlands etc haha

I've got a decat non res system mate.
Tbh, it's not ridiculously loud. Obviously idle is quite heavy, and when you floor it the thunderstorm really cracks haha, but driving at 30 in 4th/5th is fairly civilised

Wait till it's mapped and comes on boost

 

[Chino_UK]

Lol
I think it mainly is just the noise difference tbh, mapped up with a sports cat I doubt you'll see many differences. Here's a video of mine with sport cat and resonated miltek.

http://www.youtube.com/watch?v=jDiZZyIAEvU&hd=1

 

[truss]

mine bangs like ****, apparantly a flame or two with sports cat. its 3" dp though.

 

[wazza16]

wat power is yours running scott? revo stage 2 will take me around 220-235bhp 260-270 torques. Truss where do ya get the 3" downpipe from? think milltek blueflame are just 2.5"? Cheers

 

[Scott-o]

245hp and 263ftlbs torque

 

[wazza16]

thats good figures man, u get the map running sweet now? was reading bits of ur RR seen u had to go bk for him to alter it ect? if i go to him then he will be able to get it in one hopefully dont fancy travilling twice haha

 

[wazza16]

Scott, wat mods do you have with your map to to make ur figure? TB milltek, Forge TIP, MAP pipe, inlet manifold hose,open cone filter? you done the N249 and N112 (i think) bypass?

 

[Scott-o]

Yeh all them plus apr recirc valve and newsouth power gasket. N249 is bypassed and that's about it tbh. Yeh was a cold start problem and something needed changing, not sure what though! He's done my mates that's same spec since and no problems

 

[wazza16]

kewl sounds gd, was looking at ur graphs look gd! takes forever to look thru RR's haha u got couple pics of ur N249 bypass? was gonna bypass them all ordered resistors for it but if can get same results out of doin wat uve done then y not!!

 

[Hartosh1]

Damo made a guide on them bud check this out http://www.seatcupra.net/forums/showthread.php?t=200030

 

[wazza16]

Nice one cheers pal, u done this?

 

[Hartosh1]

Yeh but you get an EML light for it

 

[cupra.al]

Yeh but you get an EML light for it

thats if you completly remove the n249,its ok if you leave it plugged in.

 

[wazza16]

so can i bypass the n249 and 112 but leave the sai intact?

 

[cupra.al]

ive just bypassed the n249 and left it all in place i will get a picture for you tomorrow of how i did it.

 

[wazza16]

/cheers pal! ive got resistors if i need them!