properly

Love this interior, not keen on the white, but the doors look so much better with the soft touch plastic stuff on them.

Hey again guys. So there is another problem ( boring I know, sorry. This time rear wiper blad doesnt wipe all the surface but middle part only. I mean it doesnt wipe where it supposed to do, as wiper doesnt touch the glass in many times (ends of wiper blade).It is bosch rear blade (new) Any...

Had the cam belt on the LCR about a month or so ago and yesterday the check engine light came on. Managed to read the codes out tonight and got 2 DTCs Found: 16396 - Cam-Timing Adj. Bank 1: Retard Setpoint Not Reached 35-00 - - 16727 - Camshaft Position Sensor (G40): Signal too...

Bit of an odd one. Had a search but not had any luck really. My brother told me that my left rear light wasn't working, but when i brake all the lights work fine. So i just thought that one of the filaments had gone (double filament bulb) and a new bulb would solve the problem. It did not...

Hi. As it say above my car is not boosting properly but only when it is warm it dose not boost. When i first start driving it in the mornings the car boost fine 0.9lb but 2 mins later its not and only boost 0.5lb which you can fill the differents, is that putting the car in to limp mode? But i...

Just wondered if anyone can give me some info on the Auto Bra's for the Leon, Do they fit ok with no bonnet closing problems and with single day use (Not left on for days) do they mark or damage paint finish? Thanks in advance guys!

hi i have an 51plate Ibiza Cupra R and it is not boosting properly as from yesterday!!! i have had it looked and and none of the boost pipes seem to be broken or split. so quite unaware of what this can be??? i have not owned this car for very long, and already have done a full service and...

hi,i have an lcr with the revo stage1 and a sps3,the problem is that i dont know what the setting should be set to and am quite sure they are not set to give the best out of the car at the moment,this is the only mod which has been done apart from a atmos dumpvalve,so id like to take it...

I have just fitted a new engine to a leon cupra 02 that i bought as a project and the engine had already been removed, i have got it going but it does not seem to be pulling properly, the engine management light was on so i bought a code reader and there was 17 codes, i cleared them ,took it for...

Title says it all really, its on the drivers side window. When I press down it goes down and stays down. But when I press up when it gets to the top, it just goes straight back down again. I have to press to go up, stop before it gets there and click the switch bit by bit to get it to close...

Recently noticed the rear doors don't quite shut flush with the rest of the body. Is this a simple case of replacing the black door seal around the edge of the doors and what price am I looking at? Thanks

I have searched but i cant find anything on this subject. Maybe ive just missed it. The heater in my car is quite frankly s***. When its on number 4 it blows like it should, really strong etc. But on number 3,2 and 1 there is hardly nothing. There is alittle bit being blowen out but not...

hi guys the radio/cd on my 04 1.2 dosent sit in its housing properly,although it dosent pull all the way out it comes out about 1/4 of an inch,i can push it back in but after driving it slowly works its way out,anybody any ideas on how i can stop the radio from doing this,its really anoying:(

so she helped me do mine, in fact she did most of it which was a big help as i had ripped ligaments and cartlidge in my wrist and can put literally zero pressure on it so im a bit **** at polishing and buffing at the moment. She wants to do her car properly and hers hasnt been washed...

right folks, i fitted a boost gauge and voltmeter in a pillar pod the other day and wired it through the dash mounted light switch. D idnt think i had any probs until the other night when i tried to put my full beam on constant and they didnt work. They work fine when i pull the stalk back to...

I've just had my windscreen replaced my a mobile fitter and to me it doesn't look like it's fitted properly. The strips of black rubber along the sides of the screen don't seem to fit flush to the screen. Here's a cross-section on how it looks now: As you can see the black rubber seal...

OK, I'm ready to be laughed at. My key fob has stopped working properly. Unless I get right up to the sensor, I can't lock or unlock the doors. First instinct is that the battery needs replacing, that's why the range is so greatly reduced. But I've only had the car for two years. I've...

Car usually peaks at 1.5bar and holds at 1bar. But today it will not peak past 1bar, its felt very sluggish for the past few days i was suspecting MAF. So tried unplugging it, but still peaks at 1bar, also borrowed someone elses MAF and still no difference. What else would cause this...

Hello - I am having a problem with my rear brake lights at the moment. I have to press the brake pedal pretty hard for them to come on instead of you being able to lightly press it. This is causing some worrying situations in slow traffic. When my car went in for a service i mentioned this...