Ibiza MK3 sport updated on Cupra

[spelfor]

my 20vt bought september 21th 2009

it's a ibiza on january 2002 1.8 20 VT 156Hp just remap with little problem piping

a few pic




few hours past

Delete "Plaza" on left rear, "seat" and "IBIZA"



09/30/2009

Upper Front Strut brace Seat Sport BY MOMO fitted


Few pîc's



11/06/2009

HID kit, a aerial Peugeot 607, Glasses teinted and tail light smoked





11/15/2009

BBS LM 17"




It's too high lol



11/18/2009


Coilovers raceland





12/19/2009

in the snow






01/02/2010

First pic's of the year with one S4

 

[spelfor]

01/14/2010

my milltek exhaust and 16mm spacers





02/23/2010

:arrow: my first FMIC





03/15/2010

fitting cupra "eyes"


04/17/2010

Flywheel fidanza and Clucth Spec 2+





04/29/2010

Just on the road, I find piping with a fmic megane RS. I decided to fit my k04 turbo




the downpipe for k04-023




05/08/2010







05/11/2010

fitment k04







06/02/2010

Engine finish at 75%






paint Girling 60 double pistons audi S2



The front of my car

06/13/2010

BMC OTA 230




Front disc zimmermann et Mintex 1144 pads on etriers S2




16/06/2010


Joiner on my downpipe et my exhaust miltek



29/07/2010

cupra dash









09/07/2010

http://www.youtube.com/v/qhDc3X-SCms

11/20/2010

mapping has been reversed following the repair of leaks found everywhere on the circuit air supercharger (traductor)


result 261.7hp et 424NM ( 312.68lb/ft)

 

[spelfor]

09/28/2012

complete paint and OZ Superturismo Wheels







Listes des modifs

Esthétique :

- [del]BBS LM REPLICA 7.5X17"[/del] remplaced by OZ Superturismo Black 7X17" tyres Falken 205/40/17 -> ok
- Full black seat -> ok
- Cupra "eyes" -> ok
- Glasses teinted -> ok
- spoiler front and rear Cupra -> ok
- calandre cupra With R -> ok
- cupra R on the rear -> ok
- Tachometer cupra -> ok
- Integral paint Black magic -> ok

Moteur:

- FMIC -> ok
- Flywheel Fidanza alloy lignt -> ok
- Clutch Spec 2+ -> ok
- Milltek Exhaust -> ok
- Injectors S3 -> replaced by 525Cc
- Manifolf exhaust S3 -> ok
- Turbo k04-023 -> ok
- Downpipe K04 -> ok
- FPR 4 bars -> ok
- Remap Digiservices -> Replacement By remap MPE RACING TEAM -> on progress


Chassis:

- Strut brace upper front Seat SPORT -> ok
- Coilovers KW variante 2 -> ok
- Freins audi S2 avant -> ok
- Disc GR.N Zimmermann Front and rear -> ok
- Front and rear Pads Mintex 1144 -> ok
- Spacers 5mm front, 10mm rear -> ok

 

[Chambers_CUPRA]

Looks good mate

I'm just k04 turbo mine and what a pain.

Looks very smart

 

[spelfor]

but I don't stop here, i have extract the engine and rebuilt with wossner pistons and Con rods K1 technologies

traduction in progress

I hope my english is readable, sorry if this is not the case

 

[spelfor]

April, 7th I install the place of war



the patient installed for open heart operation



But we started to put him on crutches



and deposit him his old front brake




and a pic' for fun




April 20th

engine output is imminent, the downpipe and rear engine mounts







April 22th

Engine out





removing the gearbox, Clutch and Flywheel



Various Photos







April, 25th

First workshop on the engine mount







Open Engine















Assembly connecting rods and pistons





painting of engine







Phase Cleaning / reassembly







Thank you Compiègne rectification for cleaning combustion chambers





Cylinder head gasket


Pistons, rods, bearings, connecting rods, oil pump and oil tank lifts



cleaning the parting plane of the cylinder head



April, 26th

Brand new water pump



Timing belt distribution



May, 1st

it is a holiday but not for my engine

Rebuild of the intake manifold



Cleaning the throttle (in the back emerged two claws) :s



paint set of the intake manifold and valve cover





assembly of new injection wells





That Sunday when I was, it advances step by step

 

[ntcupra]

What did you use to help seal the injectors inserts mate?

 

[spelfor]

I use a thread seal, see this link http://www.directindustry.com/prod/loctite/thread-seals-5610-987325.html

mine is not loctite but it's the same seal

 

[ntcupra]

Cool, thank you

 

[spelfor]

05/18/2013

this week this isn't advance

I've received my discs 305X28mm For Brembo



the wishbones is Dead







05/29/2013

fitting brakes



small package for rebuild


polyuréthane Floflex

Le 30/05/2013

problem with the bolt length is too big and i've paint my carriers

before


After




repair ARB link


painted parts


06/05/2013

it's so difficult without the good tools



in place



06/21/2013

TT shifter



engine and gearbox on place



07/21/2013

step by step

fitting front face with coolant intercooler




08/16/2013

my cupra R restarted, it's good new but one fog coming probably to one connecting water or oil on the turbo and the engine idling is 1500rpm




Ce n'est pas grave je sais qu'il démarre et ça ça fait grave plaisir