Miltek exhaust

[Importcupra]

Hey Guys any 1 go any idears on how to stop the exhasut from vibrating?? it does it the whole time i drive the car and is driving me mad! thanks

 

[Robbie C]

Is it rubbing on something?

Maybe consider new rubber mounts?

 

[cupra collins]

Just find where its knocking and get urself under the car and adjust it iv got mine perfect now its a bit of trial and error but you get there in the end.

 

[p34ch3y]

it rubs on the rear beam mine dos it like a right bitch

 

[Myki da Pyki]

Use some exhaust heat wrap where its rubbing and it'l be gone then mate but the wrap aitn cheap

 

[p34ch3y]

gunna get a blue flame turbo back in the new yr so il just have to put up with it till then

 

[JIMYU]

gunna get a blue flame turbo back in the new yr so il just have to put up with it till then

i have the same problem with my blueflame lol i've been meaning to get re-inforced exhaust rubbers but haven't got round to it yet.

 

[acidstrato]

shorter exhaust mounts or raise the back end (assuming its decked)

 

[p34ch3y]

yea m8 im megga low at the back,

you cant pick it up that much it then hits the bumpper wich it pritty much is allready on mine at the mo.....

 

[cupra collins]

mines low at the back and it dont rattle at all not even on a long run with four people in the car

 

[__B3NNY__]

Move the system forward until the hangers are pointing forward, it will give you alot more clearance over the rear beam. Not sure if this will still be the case once shes lowerd after xmas. I very much doubt it

Powerflex hangers help out quite abit too.

 

[J4M3S]

exact same problem with mine at the start.

when it heated up it moved out of place but i got it up on the ramp and messed about with it and it sits nice now.

 

[Importcupra]

iv been under the car about 20 times tried to adjust it at work but still cnt, changed the rubbers. the back of my car is stupidly low, do u recon its so low that it just sits on the ream arms and cnt be helped. ( i know i could higher it but it looks good low lol )

 

[Importcupra]

just to show how low http://www.seatcupra.net/forums/showthread.php?t=122498&highlight=polo+springs

 

[acidstrato]

do u recon its so low that it just sits on the ream arms and cnt be helped. ( i know i could higher it but it looks good low lol )

DING!!

not alot you can do really

 

[__B3NNY__]

Like i said before you could try moving the system forward from the cat back, try and get it so you have the tailpipes pretty much flush with the bumper, When i done this i ended up with abot a 65mm gap between the pipe and the rear beam, admitidly im not lowerd yet but it could be worth a try.

 

[Glassy80]

Its rattling on the rear axel mate. Mine does the same thing when the car is cold, but once warmed up its fine. Take it to a decent exhaust place and they can supposedly sort it out easily enough. I've just not had time to do it yet, plus ive been thinking of replacing my standard one anyway.

 

[__B3NNY__]

plus ive been thinking of replacing my standard one anyway.

Your standard system knocks on the rear beam?

 

[Glassy80]

Yep, if you lower the back enough the standard exhaust will knock on the rear axel/beam whatever its called. I've been under there to check it.

 

[__B3NNY__]

Sorry didnt read that you was lowerd

Thats abit of a bummer then, im hoping to lower mine around 60mm on the back with a miltek system

Welcome back knocking