My leon cupra 305 whp ... 340 engine hp.. 50 kg*m

[cupra-tfsi]

Hi guys...

This my Cupra tfsi.. with:

1) Full Exhaust 76mm with 200 kat Milltek
2) apr carbonio intake + kn panel filter
3) ngk spark plugs IX iridium
4) S3 oem Intercooler
5) Forge remote divert valve
6) Bonalume Power pop off code: PS3
7) KMD fuel pump + cam follwer
8) ECU REMAP
-----------------------------------------------------
9) eibach anti roll bar 26mm fw 23mm rear
10) eibach red spring
11) all powerflex support...
------------------------------------------------------
This is the dyno result... I appreciate all your comments........ h t t p : //img522.imageshack.us/img522/2176/25042009060800x600.jpg
I appreciate all your comments.... to improve the performance , to avoid breakage, alllll...


Now i think to order quaife and sachs performance clucth and toyo r888.
I hope with this items to improve the traction.. now is low.....

 

[Poverty]

dyno dependant, but for your mods ideally it should be running around 360hp.

AMD Essex had a S3 in two or so days ago with similiar mods and made 375hp.

 

[Blade]

Hi guys...

This my Cupra tfsi.. with:

1) Full Exhaust 76mm with 200 kat Milltek
2) apr carbonio intake + kn panel filter
3) ngk spark plugs IX iridium
4) S3 oem Intercooler
5) Forge remote divert valve
6) Bonalume Power pop off code: PS3
7) KMD fuel pump + cam follwer
8) ECU REMAP
-----------------------------------------------------
9) eibach anti roll bar 26mm fw 23mm rear
10) eibach red spring
11) all powerflex support...
------------------------------------------------------
This is the dyno result... I appreciate all your comments........ h t t p : //img522.imageshack.us/img522/2176/25042009060800x600.jpg
I appreciate all your comments.... to improve the performance , to avoid breakage, alllll...


Now i think to order quaife and sachs performance clucth and toyo r888.
I hope with this items to improve the traction.. now is low.....

What software are you running?

 

[robdf2]

does that dyno max out at 340 bhp?

 

[Blade]

does that dyno max out at 340 bhp?

Had a look but can,t make much sense of it

 

[robdf2]

looks a bit weird , most grphs show 200+ bhp over what it makes

 

[cupra-tfsi]

looks a bit weird , most grphs show 200+ bhp over what it makes

dyno max power is 500 hp 4x4. i have custom ecu... initial i have install a map with max boost 2,05 bar.. and costant boost until 5500rpm of 1,60 bar and from 5600 rpm 1,4 bar until 6700rpm and then 1,25 until 7000rpm , unfortunately i don't have perform a dyno test because I was afraid that I would have broken all..... Now i have 340 hp + 50 kg*m because i have install a map with 1,75 max boost... and costant boost until 5500 rpm of 1,40 and after 1,3-1,2 bar until 7000 rpm.

 

[cupra-tfsi]

dyno dependant, but for your mods ideally it should be running around 360hp.

AMD Essex had a S3 in two or so days ago with similiar mods and made 375hp.

But with this power , they need a new piston and rod??

 

[Poverty]

But with this power , they need a new piston and rod??

no standard engine internals. Your car is a mk2 cupra right?

 

[cupra-tfsi]

no standard engine internals. Your car is a mk2 cupra right?

yes of course leon cupra tfsi my 07

 

[Poverty]

yes of course leon cupra tfsi my 07

why have you got a custom ecu? The standard one should do with a good map.

 

[Blade]

So if your running 2.05bar - thats 29.73psi on a standard turbo - Wow, don,t think it will last long. I run max boost of 1.35bar to obtain my power output.

 

[luke07cupra]

So if your running 2.05bar - thats 29.73psi on a standard turbo - Wow, don,t think it will last long. I run max boost of 1.35bar to obtain my power output.

What a safe maximum level of boost? Think mine peaks at 2520 millibar which is about 1.5bar right? - thats on Revo stage 1, going for stage 2+ shortly, not sure if thats ups the boost further...

 

[Al]

So if your running 2.05bar - thats 29.73psi on a standard turbo - Wow, don,t think it will last long. I run max boost of 1.35bar to obtain my power output.

Whats your wheel horsepower figure mate?

 

[Blade]

Whats your wheel horsepower figure mate?

315 seems to ring a bell

 

[Al]

315 seems to ring a bell

Aye should be about right lad. There seems to be a 12-15% loss between fly and wheel power.

 

[DanGB]

on my car, 350whp = 380-385hp.

 

[Al]

on my car, 350whp = 380-385hp.

10-15% then

On the Stage 2+ car I am familiar with, it was 365bhp @ fly and 326bhp @ wheels.

 

[cupra-tfsi]

So if your running 2.05bar - thats 29.73psi on a standard turbo - Wow, don,t think it will last long. I run max boost of 1.35bar to obtain my power output.

For this reason i have reduce the pick pressure a 1,75 for the standard k04 turbo and continuos boost of 1,4 bar until 55000 rpm and 1.3-1.2 bar until 7000 rpm , but i want to know if your pressure of 1,35 is costant until 7000 rpm or no...!?!?

 

[cupra-tfsi]

315 seems to ring a bell

Which type of engine mod do you have install?