Neuspeed P-flo intake

[Hilla LCR]

Is this a BSH on a Cupra?

Definitely looks like it, has the DV takeoff in place. Good find

 

[Damoegan]

Good man!

Anyone want to buy a TWINtake? lol

Give me a shout bud

Is this a BSH on a Cupra?

Yes, I think it is mate.

 

[Cupra R]

That's the one Yin. Spot the tie wrap that used to be a bolt. ;-)

 

[Bogwoppit]

If it help, here is a p-flo (k03) fitted to a mk5 Golf GTI

If it helps these photos are from an Octavia vRS not a Golf, if anyone wants to hear how it sounds and they are in Lincs then let me know.

 

[dmkay_80]

AwesomeGTI seemed to think the Neuspeed fit the K04 Cupra no problems.
Ive watched videos on youtube of the BSH & they seem to have a whistle at certain revs. Is this just crap recorings or actually happens?
On the yank sites they seem to say the BSH is quieter than the Neuspeed/Evoms, Is this true? Ths BSH certainly is a good price especially with the heat shield included

 

[Damoegan]

Just had a reply from Dubtek regatding the BHS Tru-Seal, saying that its fits ED30/Cupra fine and they can do them for £250 delivered.

 

[JCR280]

am i right that all the P-flow kits we have see so far including awesomes website are just for the K03 setup, but awesome do a kit for the K04 cupra/ed30 so this kit may have that dv take off no?

J

 

[dmkay_80]

When I called awesome on Monday they said they did a kit for the ed30/cupra for k04 turbo. I think they just have the wrong picture on website. It's only listed in vw section tho not seat.

 

[Cupra R]

AwesomeGTI seemed to think the Neuspeed fit the K04 Cupra no problems.
Ive watched videos on youtube of the BSH & they seem to have a whistle at certain revs. Is this just crap recorings or actually happens?
On the yank sites they seem to say the BSH is quieter than the Neuspeed/Evoms, Is this true? Ths BSH certainly is a good price especially with the heat shield included

The three intakes you mention mate are all the same if not very similar construction, so for me they should all sound the same.

With regard to whistling, think this will be due to crap recording's.

 

[Cupra R]

Just had a reply from Dubtek regatding the BHS Tru-Seal, saying that its fits ED30/Cupra fine and they can do them for £250 delivered.

I'm sure they used to be alot cheaper than this, is the £ that crap

 

[dmkay_80]

k04 one will be a larger bore too, so would fill the engine bay better..

Is this true. I was under the impression it was the same only with the dump valve take off?

 

[Damoegan]

Is this true. I was under the impression it was the same only with the dump valve take off?

Well I would expect the inlet for a k04 to be larger than a k03, so therefore the whole pipe should be larger bore....

Could just be a different size silicone connector though ...

 

[dmkay_80]

I think a call to Awesome in the morning is required lol. I dont have a clue about intake dimensions of K03 & K04

 

[dmkay_80]

I must admit this cheap kit did catch my eye. It just needs a dump valve take off welding on & a decent filter but the price of a good filter wouldnt make it much cheaper than the Neuspeed or BSH.

http://cgi.ebay.co.uk/NEW-Air-Induc...arts_Vehicles_CarParts_SM&hash=item1c12246a54

 

[Damoegan]

You could get a local exhaust company to weld on a DV take off

 

[Cupra R]

I must admit this cheap kit did catch my eye. It just needs a dump valve take off welding on & a decent filter but the price of a good filter wouldnt make it much cheaper than the Neuspeed or BSH.

http://cgi.ebay.co.uk/NEW-Air-Induc...arts_Vehicles_CarParts_SM&hash=item1c12246a54

I be a littl!e oncerned as to whether or not correct maf scaling has been taken into consideration before buying just any old intake mate.

Stick with tried and tested if possible.

 

[dmkay_80]

I be a littl!e oncerned as to whether or not correct maf scaling has been taken into consideration before buying just any old intake mate.

Stick with tried and tested if possible.

I never thought of that. At that price its probably not been checked.

 

[kezFR07]

Is this a BSH on a Cupra?

this the neuspeed p flow?

 

[markgb]

HMM, interesting reading. I really need an induction kit on mine as I miss the noise of my old LC and LCR. Can't really justify the outlay of the ITG, and don't like the look of the twintake's. Will have to watch this space to decide on which one I go for.

 

[dmkay_80]

this the neuspeed p flow?

No its th BSH