What do you think of these headlights?

[WHOZBOSS]

Nice work mate

 

[Willz17]

How would it be possible to not turn on LEDs mate?
As I have auto lights and both side and main lights come on same time =\
Also I could drive with lights off all the time until I get the canbus box although I drive alot at night therefore I will need to use lights =[

 

[Jarre]

Yeah the DRLs are configured to come on when the ignition is on. The only way to stop them coming on would be to turn the sidelights on before starting the engine, then leaving them running the whole time the car is on

 

[Deleted member 74601]

Still haven't heard any from the FL ones I've found, I'm destined not to have any

Mind end up buying the official headlight and just not the washers etc.

 

[paul7619]

Your car is looking well sweet, well done you must be happy with the new look. With regards to the LED canbus box, i never recieved the same box with my lights either. I hope the company sort it out asap not like where i bought my lights from, i ended up buying 2 load resistors which has sorted it out now, so now error on dash and lights cutting out.... So whats your next mod your going to do to your car

 

[Adman77]

They look pretty good actually! Pleasantly surprised!

 

[Willz17]

Your car is looking well sweet, well done you must be happy with the new look. With regards to the LED canbus box, i never recieved the same box with my lights either. I hope the company sort it out asap not like where i bought my lights from, i ended up buying 2 load resistors which has sorted it out now, so now error on dash and lights cutting out.... So whats your next mod your going to do to your car

Thanks mate,

And you mentioned 2 load resistors, by any chance do you have a link for these? Just incase i cant get my hands on that canbus box.
Note: Where the load resistors easy to fit? Litterally plug and play?

Also gutted! the front bumper has to come off again soon as i found out my headlight washers have stopped working!!! Must of accidently unplugged something without knowing =[ My bad for not checking if everything is working before putting bumper back on -.-

 

[paul7619]

Hi i dont know how to do LINKS to show you what i bought, but you are after. 2 x 50w 6ohm load resistor with scotch block connectors.. These resistor will replace where the led canbus box will go. No cutting wires. The cost is around 5 pounds

 

[Willz17]

Hi i dont know how to do LINKS to show you what i bought, but you are after. 2 x 50w 6ohm load resistor with scotch block connectors.. These resistor will replace where the led canbus box will go. No cutting wires. The cost is around 5 pounds

ok thanks mate, to paste a link (all you have to do is go to website where resistors are, then select/highlight weblink, copy it, and the simply paste in this thread ^^

 

[paul7619]

http://www.ebay.co.uk/itm/2x-50W-LO...1120255844523222529&pid=100015&prg=1006&rk=1&

 

[G5RBY]

Lights look brill. Will definatly be buying a pair of them once back my holidays. Look way better than standard. Glad I can see them on a car

 

[TarekElsakka]

Hopefully you'll receive the canbus kit from them as that's your right. If not, you can probably sue them or make a claim, as that's what you paid for.

For the time being, though, you can try your luck with load resistors from http://www.hids-direct.co.uk they have plenty over there.

 

[Willz17]

http://www.ebay.co.uk/itm/2x-50W-LO...1120255844523222529&pid=100015&prg=1006&rk=1&

Thanks mate =]

 

[Willz17]

Hey paul7619, The resistor box is getting sent to me and i should recieve this shorty from autoart =]
By any chance do you know which screw adjusts the light beam light? As i will need to allign the headlights myself to prevent me from dazzling people!!!

There are 2 screws but not sure which one? Can you post a picture showing which screw adjusts the light beam? Let me know

Thanks mate,
I will upload pictures when my lights work 100% =]

 

[Jarre]

One screw will be up/down and the other will be left/right

 

[paul7619]

Hi Willz17. I had my lights adjusted when i had my MOT, so go no idea but i guess Jarre has answered your question.. What remap did you get and where as im from Llanelli

 

[TarekElsakka]

Is it possible to adjust the lamp of the high beam bulb that way in the stock headlight units? The OEM, non-projector lens that came with the car? The reason is that I feel like my Nightbreaker Plus bulbs are a tiny bit high and I'd like to lower them a little bit but I also know that the bulbs are in perfectly so it's the lamp that would be lowered.

 

[Willz17]

Hi Willz17. I had my lights adjusted when i had my MOT, so go no idea but i guess Jarre has answered your question.. What remap did you get and where as im from Llanelli

Hey Paul, can I ask of a Favor? Can you take a picture of the back of your headlights for me?
I want to see if you have fitted the electronic levellers from ye standard Leon headlights.
I got the car remapped by Dave @ Elite remaps. He's mobile so he comes to you! Good cheap price and the remap is good =]

 

[Willz17]

Finally! Headlights completed

Finally, the missing canbus/resistor pack had come through the post yesterday, so this morning i quickly connected them up with the headlights before i went to work. Got to admit, i love the new look =]

Here is a picture to show results (will take more later after work when it gets darker)

LED Lights Off:

LED Lights On:

What you guys think?
Also for people who have these lights, Have you fitted hid bulbs into them? Any risk in melting the projector lenses as hids get hotter than halogen?

Let me know
Thanks

 

[Deleted member 74601]

I hate you. Stupid suppliers not having any facelift lights.

With regards to HID bulbs, I'd imagine normal 35w ones will be fine.