limit

What would be the hp limit on my AUM (if I change the rods) running stock pistons 9.5:1 and small port head? 400bhp possible? More? Less? Cheers!

Hello all, I had some serious issues with my LCR over the weekend on a long journey.When i set off i knew something didn't feel right, when i put my foot down it just didn't feel right, sort of held back a bit. So anyway, while cruising on the motorway at 120kph in 6th gear with low...

Hi guys, i am getting a facelift leon fr in 2 weeks, my question is what is the max size usb stick i can insert into the usb slot that the stereo will accept?

Hello, i have an 02 leon cupra, it has had a remap a couple of years ago, just recently i have noticed that its not quite right. It is fine up to about 4.5 revs then the power just drops, the max speed i can get out of the car is about 118mph! I have had a lot more out of it than that. I have...

Hi Guys, Just done a quick scan on a work colleagues car as she said there was a warning light on. Albeit the warning light wasnt connected to this, the following code came up: 17916 - Idle Sys.Learned Value Upper Limit Attained P1508 - 35-10 - Intermittent Any ideas what...

got this code 17550 P1142 Load Calculation Cross Check Lower Limit Exceeded what do i change to fix this?

Hi everyone. Current spec. Standard AUQ 180 engine. T28 turbo from a Nissan Pulsar Custom Exhaust to be made. Looking at Geneisis 550cc injectors. Standard at the minute. QPENG ECU. Walbro 225l/h in take fuel pump. I was looking at 300 BHP when mapped. Is this too conservative...

I have a 2.0TDi Stylance, is it right that with the clutch depressed the engine will only rev to 3k? TIA

i have a 2000 toledo it started to buck in idle,dealer said it was the lamda probe ,had it replaced same problem 'lamda probe 'upper limit'.can anything else be causing this problem

Hi all, im new to this forum so please be patient with me. finally got myself a MK3 cupra and have big plans for it. However does anybody know the kinda power limit before having to forge the engine? iv heard around 350bhp but would like to hear this off a few more people.? Any help would be...

As title? Oil service indicator came on last week, this morning I noticed I'm low on boost. Seems OK'ish up to 2k, then struggles and can't hear the turbo. Still gets to 4k, but sounds hollow. Guess it could be bad news, or a simple reset the service indicator fix! I'm leaning...

Guys I needs some Help I keep getting this fault code. This throws up the EPC light and cuts all the power until i switch the ingnition off/on. This is happening randomly always on part throttle. I've done a search on this and found a few threads but nothing to confirm what resolved the...

I got this today...I put my old MAF back in and drove it yesterday and all was fine. Driving into work today I wasnt booting it but I was on my way up to 70 and the boost cut out completely. From then on the turbo wasn't spooling up at all and on my gauge wasnt even getting to 0 it was just like...

Hi guys if i was to up the rev limit on a 16v abf engine currently as good as standard how high will the abf lump go before it goes bang? What would a sensible limit be or should i not change it from standard?

Looking at getting a remap on my pd130 but want the torque limiting to below 260ish lb.ft Which tuners can do this? Are there any mobile tuners that offer this service? Thanks

Dear All, I understand the need for methods of preventing spammers and evil do'ers running riot across internet forums, however I feel the posting limit on the "For Sale" section is too high. The only way I can talk to a potential seller is by bumping up my post count with random stuff...

Hello guys, I want to know if a fricting plate is enough to increase your torque limit, if the friction plate can handle it? Or do you need a complete kit? Thanks

I've gotta ibiza 2.0 8v on a 97/R after an overheatin problem i've replaced the head gasket but whilst doin that the hall sensor (on the side of the dizzy) went tits up and needed replacing. Now, the car is hittin the rev limiter at 5000 rpm. Any ideas???