Black Badges....

[Brighton Femme]

I like that! Well Done.. looks top notch and very stealth!!

 

[Ruddmeister]

Thanks

Hope to get it finished tonight

 

[Brighton Femme]

Would look the daddy with black and silver plates!!! Are yours reduced size ones?

 

[Ruddmeister]

Would look the daddy with black and silver plates!!! Are yours reduced size ones?

LOL I have silver and black plates in the garage but they are too dodgy so I took them off, yes front plate only is 3/4 size

 

[Brighton Femme]

haha.. same here! i've got pressed Alu plate.. but too scared to put them on!!! There not even reflective!!!

Is the reduced size one still legal? Have you got the same size front and back?

 

[Brighton Femme]

Also where'd you get your Revo badge from?

 

[Ruddmeister]

haha.. same here! i've got pressed Alu plate.. but too scared to put them on!!! There not even reflective!!!

Mine either

Is the reduced size one still legal? ?

Erm probably not (sourced at Fancyplates.com page 2 of the order process allows you to select size of front plate)

Have you got the same size front and back?

No Rozzer friendly full size rear

Brighton Femme Also where'd you get your Revo badge from? ?

The R is just moved accross and the 'evo' comes from your Local Revo distributor or PM Kev and beg, flirt etc should post you a few

 

[Brighton Femme]

The R is just moved accross and the 'evo' comes from your Local Revo distributor or PM Kev and beg, flirt etc should post you a few

You got any close up pics?

 

[Daz8161]

emm was thinkin...... would it look nice if the centre badge was kept chrome but the edge of the centre grille (chrome bit) was sprayed black?

 

[Ruddmeister]

emm was thinkin...... would it look nice if the centre badge was kept chrome but the edge of the centre grille (chrome bit) was sprayed black?

Post some pics when you have done it

 

[Ruddmeister]

You got any close up pics?

only this

 

[StuRox]

haha.. same here! i've got pressed Alu plate.. but too scared to put them on!!! There not even reflective!!!

Is the reduced size one still legal? Have you got the same size front and back?

I have always had a smaller front number plate, and as long as you use the original plate, and then cut it down, and leave 1cm from the edge of the letters to the edge of the number plate - then it is perfectly legal, as the law just states the height spacing etc of the letters, and the spacing between the edge of the plate and the letter - so job done.

And I have never had any problems with the plate whatsoever, and neither has my mrs with hers too.

So go on, get out that saw

 

[Brighton Femme]

saw! I can't cut straight! My mates got a dremel tho!

 

[StuRox]

saw! I can't cut straight! My mates got a dremel tho!

ohhh, wouldn't use a dremel, only to round off the corners, but even then a bit of sandpaper will do the trick - you will get a straighter line with a saw.

 

[andycupra]

http://cgi.ebay.co.uk/Seat-Ibiza-Le...582942435QQcategoryZ10404QQrdZ1QQcmdZViewItem


?????

 

[Ruddmeister]

http://cgi.ebay.co.uk/Seat-Ibiza-Le...582942435QQcategoryZ10404QQrdZ1QQcmdZViewItem


?????

Aye but I did the chrome surround too

 

[Ruddmeister]

Anyway finished look with 2 coats of lacquer

 

[Daz8161]

any pics from further away?

 

[Ruddmeister]

any pics from further away?

no sorry plus it's dark now

 

[FriarFR]

shoot me if this is a daft question, i'm being lazy and i've never checked..., but is it easy/possible to remove the centre grille section? has anyone considered putting in one of those grilles without an S on it, and only the vertical bars...?