Yea, it's a complete rip off mate. It's just a JR/Green Cone filter with a bit of metal bashed into shape. You could buy a cone and have the shield fabricated for less than half price!
-
Guest, 🚨New Stock alert: Premium CUPRA valve caps now available in the store 👉 Order now from the merchandise store
Mine hits 160 at around 4k and is at 170+ @ 6k+rpm.
The logs i was looking at the other day were done with IC etc
176 was the best i saw last night. Highest intake temp was 25 deg C
That was even after 4 full flat out 1st,2nd,3rd, 4th runs. IC and intake doing there job nicely!!
The logs i was looking at the other day were done with IC etc
176 was the best i saw last night. Highest intake temp was 25 deg C That was even after 4 full flat out 1st,2nd,3rd, 4th runs. IC and intake doing there job nicely!!flashbsd
Guest
well ive just been out with mikeibizacupra, and my MAF doesnt seem to be at fault, it pulls the same readings with his MAF and a different air filter.
What else could be stopping the airflow to the MAF sensor? surely its not the turbo?
What else could be stopping the airflow to the MAF sensor? surely its not the turbo?
flashbsd said:well ive just been out with mikeibizacupra, and my MAF doesnt seem to be at fault, it pulls the same readings with his MAF and a different air filter.
What else could be stopping the airflow to the MAF sensor? surely its not the turbo?
do you have some logs of block 115/118 ? i'm curious to see if boost/temp are in relation with maf readings.
flashbsd
Guest
Martyn said:
I shall do this at the weekend matey, would that cause low airflow then if there was an issue? surely the maf readings though are'nt to do with the intercooler?
TIP looks fine, ill go under (oohh err) at the weekend and check its all seated properly with no kinks etc.
Mart, it could well cause the low readings, as could a blocked exhaust, or a colapsed CAT etc...imagine the engine and turbo as a big air pump
Last edited:
flashbsd
Guest
anybody got another std exhaust/cat setup for me to borrow?
I am just fed up now of trying to fix it all etc.
Intercooler 1st port of call.
Anything else you reckon could help this poor sole out? :'( the other thing i might do, is fit the ecu to a k03s car, ensure its pulling the airflow, so its not my car at fault or soemthing.
I am just fed up now of trying to fix it all etc.
Intercooler 1st port of call.
Anything else you reckon could help this poor sole out? :'( the other thing i might do, is fit the ecu to a k03s car, ensure its pulling the airflow, so its not my car at fault or soemthing.
Me and Mark were chatting about this last night...the ECU swap is a fairly easy check to run but you'd have to bear in mind that your map was setup for your FMIC and it might run a little 'too' hot for a car with a side mount (pull more timing and hold the car back). Looking at your boost logs, running your ECU on a with a K03 wouldnt cause any issues as your boost levels are still well within the K03 turbos capabilities.
Last edited:
flashbsd
Guest
yep no problemo, for a quick run as you say it should at least tell me if its my car or not
Well we now know its a restirction of some sort, cos it wouldnt be the MAP requesting 146 would it? doesnt work like that surely.
Well we now know its a restirction of some sort, cos it wouldnt be the MAP requesting 146 would it? doesnt work like that surely.
Bit heath robinson but if you took the cat out etc so you have a free flowing zorts could you di a quick run to see if that helps? As that woud mean its the restrictions in your zorst?
Cat is part of the DP dude...it'd also result in a CEL unless Jabba have disabled the CEL on failed Cat alert in the code.
flashbsd
Guest
yup cant take cat out on a mk3 without stage 2 revo.
I will do a log on the way home and post up later on
I will do a log on the way home and post up later on
flashbsd
Guest
i've just spoken with nick, and he said it could well be the exhaust, if the gasses arent escaping quick enough, its not gonna be pulling in the readings.
we seem to think its definatly the out side not the intake now, wierd aint it.
Now all i need tyo do, is before i go out and buy a whole exhaust system, find soembody with full milltek/catback to try out on the car.
that is going to be a real long shot, but worth a go. Helpful people are always good to know!
we seem to think its definatly the out side not the intake now, wierd aint it.
Now all i need tyo do, is before i go out and buy a whole exhaust system, find soembody with full milltek/catback to try out on the car.
that is going to be a real long shot, but worth a go. Helpful people are always good to know!
Jonzy
Guest
I think the phrase if a job is worth doing, it's worth doing properly comes into play here.
Proper half arsed attempt really, and you wonder why you've got problems!
Proper half arsed attempt really, and you wonder why you've got problems!
Wouldnt the DP be the biggest cause of these problems? BF DP and milltek back id say. And im sure there was a milltek cat back going in the for sale section?
Similar threads
