• Hey Guest👍👎 We're looking for reviews of your local CUPRA or SEAT Dealership - it's quick and easy to do: Leave a review now
I would personally:

- buy all new bolts
- replace the o-ring for the oil pickup (buy original if possible)

@iammooks You got this

Sound advice there - some things you can't take any chances with, and bolts and o-rings are right up there.

09093d000e6565b22b790fd5e7ad3cb1.jpg


Everything is back together again now. Turned the engine over to bleed the coolant and nothing concerning happened. No coolant spraying everywhere, no fumes at all in the engine bay, and the slight slack in my steering seems to have gone too, but I'll find out when I actually take it for a drive. At the moment the undertray is still hanging off until I put the chimney clips in to finally hold the front bumper in place properly. There's another job I've been meaning to do for years.

Cleaned up a bit while lots of stuff was out. It'll never look as pretty as the Cupra R engine bay, but once the engine cover is back on, it'll be passable.

One of the EGR to intake manifold threads stripped, so I'm going to use a longer bolt with a nut on the other side. So glad I've got the space there to do it - otherwise I'd probably have to learn how to do a helicoil. Annoyed at myself for missing it when it was out, because there's no space for a drill. But hey, the nut and bolt will do the job perfectly, so it'll be fine.

Probably spent more time and money on the car than it's worth by a long way by now, but that's not why we do it, it's it?


Sent from my iPhone using Tapatalk
 
Sound advice there - some things you can't take any chances with, and bolts and o-rings are right up there.

09093d000e6565b22b790fd5e7ad3cb1.jpg


Everything is back together again now. Turned the engine over to bleed the coolant and nothing concerning happened. No coolant spraying everywhere, no fumes at all in the engine bay, and the slight slack in my steering seems to have gone too, but I'll find out when I actually take it for a drive. At the moment the undertray is still hanging off until I put the chimney clips in to finally hold the front bumper in place properly. There's another job I've been meaning to do for years.

Cleaned up a bit while lots of stuff was out. It'll never look as pretty as the Cupra R engine bay, but once the engine cover is back on, it'll be passable.

One of the EGR to intake manifold threads stripped, so I'm going to use a longer bolt with a nut on the other side. So glad I've got the space there to do it - otherwise I'd probably have to learn how to do a helicoil. Annoyed at myself for missing it when it was out, because there's no space for a drill. But hey, the nut and bolt will do the job perfectly, so it'll be fine.

Probably spent more time and money on the car than it's worth by a long way by now, but that's not why we do it, it's it?


Sent from my iPhone using Tapatalk
If there was a cupranet award for most time and effort put into one car then I think you won it. I’m impressed at how you’ve kept the motivation!!👍
 
One of the EGR to intake manifold threads stripped, so I'm going to use a longer bolt with a nut on the other side. So glad I've got the space there to do it - otherwise I'd probably have to learn how to do a helicoil. Annoyed at myself for missing it when it was out, because there's no space for a drill. But hey, the nut and bolt will do the job perfectly, so it'll be fine.

Probably spent more time and money on the car than it's worth by a long way by now, but that's not why we do it, it's it?
If the fix doesn't work, I think I have at least one spare inlet manifold you can have
 
  • Like
Reactions: iammooks
If there was a cupranet award for most time and effort put into one car then I think you won it. I’m impressed at how you’ve kept the motivation!!

I'm so broken... I've either been on the floor under the car not knowing which way is up half the time or bent over the engine with my hands in awkward places trying to get to awkward bolts. Caked in carbon half of that time too. Make that 90%. And that's on the low end, really. I'm mentally and physically broken, but it seems to run better. Less play in the steering, but there have been some tight spots in the steering that are definitely more noticeable now. I don't want to have to take the rack out, I really don't.

Before I forget, check this out:

2d2561077cfe315ac411a33d6d491942.jpg


It was running cold for a while, so I took the long way home from the supermarket, after checking the coolant levels in the car park. All of a sudden, it came up to temperature, super smooth, and stayed there. Dead centre. Beautiful thing to see, it really was. Means the thermostat I put in is working, opened up when it was supposed to, and it meant the coolant had got where it was supposed to, rather than on the Lewes Road. And it means the coolant temperature sensor I put in is actually working and was telling the truth when the engine never really got up to temperature.

Made it all worthwhile.


Sent from my iPhone using Tapatalk
 
Last edited:
done the yearly oil/filter change hoover the pollen and k&n as i recent cleaned and re-oiled that .. oh and when a milk container bursts in the boot make sure you clean it up correct as once it drys it stinks as i only wiped it up, used a crap load of carpet cleaner and fabric freshener
 
Telltale condensation on the windows and wet carpet in the rear passenger side footwell. I know I put new butyl tape in when I replaced the lock, so I'm hoping it's just that the drain holes at the bottom of the door are blocked - I've noticed water sitting on the sill when I open the door, so maybe just a good old clean will sort it out.

It's not like I can't re-seal the door - I can do the job in my sleep at this point - but I'd just like to go one winter without towels under the carpet and moisture traps in the car.

Some gratitude for all the work I've done this past month...


Sent from my iPhone using Tapatalk
 
IMG_0958.jpeg


Takes 5 months for a tight handbrake at its service to go to a signal box lever.

What is the definitive tool to get this bloody screw tightened? I've bought various deep sockets and tools and there's never any room because this car seems to be the only Mk4 Golf platform without any space to do it
 
I've bitten the bullet & finally acted on advice from here & another garage regarding the poor service my car had this summer. I've taken it up as a consumer rights issue, as a failure to adequately repair or compensate for the fact that the car's issue is worse than when it arrived, & at the expense of £1100 + £60 tow truck home.
I have sent them a legally binding letter of complaint, which if no response or not satisfactory, then it will progress to the motor ombudsman. A local garage have offered me backing, as they say the whole handling of my car's issue, component replacement instead of actual fault finding, & the overall cost was totally unacceptable & a failure on their part.
I'm not happy about any of it, but now I literally have nothing to lose. I was shafted & the service was sloppy, so at least having an honest garage encourage me to fight back with their knowledge & expertise to back me up has helped. I just wish they could have fixed it properly in the first place. Not too much to ask is it? 🤬
 
Last edited:
I've bitten the bullet & finally acted on advice from here & another garage regarding the poor service my car had this summer. I've taken it up as a consumer rights issue, as a failure to adequately repair or compensate for the fact that the car's issue is worse than when it arrived, & at the expense of £1100 + £60 tow truck home.
I have sent them a legally binding letter of complaint, which if no response or not satisfactory, then it will progress to the motor ombudsman. A local garage have offered me backing, as they say the whole handling of my car's issue, component replacement instead of actual fault finding, & the overall cost was totally unacceptable & a failure on their part.
I'm not happy about any of it, but now I literally have nothing to lose. I was shafted & the service was sloppy, so at least having an honest garage encourage me to fight back with their knowledge & expertise to back me up has helped. I just wish they could have fixed it properly in the first place. Not too much to ask is it? 🤬
has the new garage looked at your car yet ?
 
has the new garage looked at your car yet ?
No, they wanted to hold back until I approached the original garage (to prevent any possible conflict of interest).
The original garage have refused all responsibility, blaming me for agreeing to work, but they have missed out the fact they did not investigate the actual problem & replaced components, instead of actual fault finding. I will take it to the motor ombudsman if my secondary letter of dissatisfaction is rejected.
 
Last edited:
Well, let's see if that works...

b196c7da00adffe586a770a855f7436b.jpg


Took the weather strip out of the car last Friday to clean it up and to check the drain holes in the bottom of the door. It rained pretty hard yesterday morning though, and I could see there was water on the sill again. Fortunately with the door card off, I could see where the water was coming through...

266f2d5280bafec3613fe0335a8befd7.jpg


I didn't replace the butyl tape when I replaced the lock a couple of years ago, hence it looking a bit messy. It held fairly well up until now, but if you zoom in, you can see drops of water. When I levered the inner door skin off, water came through from the sealant below the speaker, as well as the bottom of the speaker housing itself. I wasn't any to start drilling out the rivets and resealing that, so the butyl has all been replaced, and I ran some silicone sealant around the speaker housing too.

The new butyl looks a lot cleaner now too. Don't want anyone thinking I might have done a half-arsed job of it...

After cleaning up the weather strip, I decided to put new 3M adhesive on too.

d5f34f5ac9c15a68f5dff95612bb7d83.jpg


Will wait until it next rains (give it an hour or so...) to see if it's worked before I put the door card back on. Noticed while I was tidying up that the passenger front door has water on the sill now too. That's the only door that's never had the seals replaced, so it kind of deserves some fresh butyl after holding out all that time. I haven't done a front door for a while now, but I know it's easier than mucking about with that bloody peg and dowel arrangement in the rear doors...


Sent from my iPhone using Tapatalk
 
i got rid of those rubber strips along the bottoms of the doors and also cut small v's into the door seal itself directly under the drain holes on the door, works perfect, when i open the doors after a heavy rain spell i can see the water has been escaping from the v's i cut.
 
any hole that's not filled on that inner door panel like for example the plastic bracket that holds the lock as most of the time people remove or remove as there broken , block the holes as water will come though it you can test that by running water outside the window
 
Well, let's see if that works...

b196c7da00adffe586a770a855f7436b.jpg


Took the weather strip out of the car last Friday to clean it up and to check the drain holes in the bottom of the door. It rained pretty hard yesterday morning though, and I could see there was water on the sill again. Fortunately with the door card off, I could see where the water was coming through...

266f2d5280bafec3613fe0335a8befd7.jpg


I didn't replace the butyl tape when I replaced the lock a couple of years ago, hence it looking a bit messy. It held fairly well up until now, but if you zoom in, you can see drops of water. When I levered the inner door skin off, water came through from the sealant below the speaker, as well as the bottom of the speaker housing itself. I wasn't any to start drilling out the rivets and resealing that, so the butyl has all been replaced, and I ran some silicone sealant around the speaker housing too.

The new butyl looks a lot cleaner now too. Don't want anyone thinking I might have done a half-arsed job of it...

After cleaning up the weather strip, I decided to put new 3M adhesive on too.

d5f34f5ac9c15a68f5dff95612bb7d83.jpg


Will wait until it next rains (give it an hour or so...) to see if it's worked before I put the door card back on. Noticed while I was tidying up that the passenger front door has water on the sill now too. That's the only door that's never had the seals replaced, so it kind of deserves some fresh butyl after holding out all that time. I haven't done a front door for a while now, but I know it's easier than mucking about with that bloody peg and dowel arrangement in the rear doors...


Sent from my iPhone using Tapatalk
Good job 👍
 
4690bce80900c2d53b2fd90f5caf3165.jpg


Water on the sills this morning, but then, it really came down last night. It's rained all day today too, but the sills were dry when I checked them before it got dark, so day of rain and no more water, so


Sent from my iPhone using Tapatalk
 
  • Like
Reactions: Alexis27