results

Just got back from motorscope with these reults: 193 and 285Ft of torque. I got 169 and 277Ft of torque when standard at Jabba. I am goin back to Jabba to get it rrd next week so I can properly compare the figures to the standard ones I got at Jabba a few weeks back...

Just come back from Jabba. Cupra got 169.6bhp and 377nm of torque:clap: . Very happy with the results and the curve is good. Its completly standard except for green cotton filter. I will get the graph on in the next few days. Cheers

My Mk3 Ibiza had a custom remap @ Star performance last week here are the results. Modifications:- - K03S Turbo - Blueflame D/P + 100 cell race cat (heatwrapped) - Forge DV - Forge TIP - 4 bar FPR - Jabbasport FMIC kit - Jetex cat back - Dynatwist Green Ind kit Fuel used:-...

results and write up here> http://forums.vwvortex.com/zerothread?id=3098525&page=1 Confirming some of their flow results is my own 007 big port mani with r32 tbody... gained 30bhp/22lbft over the dual plenum big port mani on stock tbody i ran before.

got the car rolling roaded at Surrey Rolling Road, and i am happy with the results the remap was done by P-Torque, and i ended up with 160bhp and 280lbft not too bad aye????

Well after a good few months, here it is, a full VAG Cars RR Day write up. The rolling road day took place at Awesome GTI in Manchester, and in total we had 24 cars running on the rollers throughout the day. To start with here’s some pictures of the cars outside during the whole day;

had my ibiza mapped @ jabba yesterday, my mods are green dynatwist forge 007dv samco TIP K03s turbo Forge actuator Forge FMIC Blueflame 2.75" in downpipe blueflame 2.5" system 4 bar FPR made 232bhp @ the wheels :D which they calculated to 250bhp because i have standard wheels on...

hi all. just got my car rolling roaded this morning and i am not very pleased with the BHP.... My car is revo remapped, bf full system, tip, 4bar fpr, divert valve, enclosed induction, and bigger mas flow cylinder.... 247.5 bhp 297.0 ft.lb i was...

I fitted my new Forge 007P DV at the weekend, in the vein hope of trying to cure the 'limp mode' power loss problems I've been having. It occasionally kicked up error codes and went into limp mode, and when I checked with VAG-COM it seemed to point to the DV. Well, ordered a 007P and it...

Logged Custardcupras (IHI stage3 22-23psi) car today multiple consecutive 4th gear 2000rpm to 7500rpm runs (3-4) resulted in a max of 39 oC inlet temp this is with aquamist but no methanol. Looks good to me and its seems like its well upto the job.:D

Where is the best place to go to get an honest and true power output for your car

Ok guy`s, a fantastic day all round as I`m sure you`ll agree and a good turn out. Got off to an iffy start but that`s another thread! Mostly happy people and some not so happy but people should realise it was 92 degrees in there today so this does really need to be taken into consideration...

:cry: After having stage 1 revo two weeks ago i had my car on the rollers on sunday with disappointing results (see below). i have a bmc carbon airbox and forge dv and im pretty sure it should be making much more than what it has. the car itself seems to run fine with no boost leaks, hits...

Well today i went to a rolling road at powerstation in Gloucester. As today is so hot the temps even in the dyno room were high :( :( (29 degrees ambient) Anyway i managed to pull 199bhp @ 4685rpm 235lbs torque @ 4015rpm I think my power is down because of the high temps? What do...

Sunday 18 June 2006 14:00:07 06A 906 032 HN 1.8L R4/5VT 0002 Group A: '118 Engine Speed Air Temp In Boost Dut Cyc Actual Boost TIME 700-6800 RPM <=110 C 0-100% <=1800 mbar MARKER STAMP /min °C % mbar 0.01 2200 48 95.3 1120 0.4 2240 48...

Hey all... Here are my 4 wheel alignment results from last week. Now, does anyone care to comment on these? The car still pulls to the left badly (IMO) and I want to improve it, but I really cant see what else to do. I've had this problem since buying the car about 2yrs ago. Since...

Hi all just been to jabba for my remap today and very happy with the results my mk3 ibiza cupra managed 200.1bhp with 239.8ft/lb of torque. Now looking forward to pod on sunday to hopefully knock my time down a bit how do these results compare to everyones?

Just a quicky for anyone that has fitted their tip then logged flow afterwards, is there an increase in flow, if so what sort of improvement was there, both figures and ass dyno? cheersamundo. also on a red car, red or black? blue is out...

Me and Olly20vT went to Stealth today to dyno our cars for the 1st time...... 218.1BHP @ 4779RPM & 261.0 lb/ft @ 3729RPM Thought mine did quite well taking in to account that it still has a standard CAT! :D 253.6BHP @ 5183RPM & 275.5 lb/ft @ 4189RPM Olly's results were also very...

245,9 hp and 304 Nm: http://www.filedump.nl/getmedia.php?img=Photograph.jpg Spec's: Custom remap by JD Engineering (Jeroen Dik) Forge DV Full Milltek 4 bar FPR Nice figure's:funk: Only the torque needs to be higher, so JD Engineering needs to boost up the turbo a bit.