DPJ's GTRS Eliminator Install and Development

[wild willy]

Some goodies waiting to go on the car.

(Resistors not shown )

Brilliant minds think alike.
Thats exactly what i had in mind with forge. The only diff is i would use a 3inch T for the DV.
How are you going to manage for the other spouts. can you use a similar idea as the method used for tapping your methanol install into the pre throttle pipe work.
Also look at the custom work JBS are using for thier tips.

 

[The MoffMeister]

is this the tip then dave?

 

[DPJ]

Brilliant minds think alike.
Thats exactly what i had in mind with forge. The only diff is i would use a 3inch T for the DV.
How are you going to manage for the other spouts. can you use a similar idea as the method used for tapping your methanol install into the pre throttle pipe work.
Also look at the custom work JBS are using for thier tips.

There's a piece to come - to go between the two 90s

is this the tip then dave?

Yes. A bit of pruning as well as all the silicons are too long.

 

[The MoffMeister]

cool nice one

 

[DPJ]

The teapot TIP coupler

Made by ProAlloy to my design.

 

[wild willy]

Dave thats top work. You kept that quiet. I just may have to obtain one myself if possible. Can't wait to see the large bore tip results.
I'll be dreaming of your TIP tonight.
Can I ask how much it cost you.

 

[The MoffMeister]

i knew as i have one to haha


first time i've seen it though cheers again dave

 

[wild willy]

i knew as i have one to haha


first time i've seen it though cheers again dave

Secret squirrels.

 

[The MoffMeister]

eh you have to be very special for this group and we're so secret we dont even know the secret group name

 

[DPJ]

Secret squirrels.

PM sent Carl. You're one too now!


In answer to the question, not a lot. If anyone wants one, Wayne at ProAlloy has the design.

 

[wild willy]

Cheers.
You fitting it tomorrow Dave, with the large turbo inlet collar fitted.

 

[DPJ]

Your PM's full Carl.

The small take offs are 7mm Carl. 5mm Silicon will squeeze on no probs. I'm using 8mm where I can.

 

[DPJ]

This whole thing is dependent on the following piece fitting:

The Omega Shifter Cable bracket. Not as pretty, but I'm pleased with it.

I was designing a bracket to carry the shifter cable over the TIP and it was a box-like structure. It was getting complicated strengthening it. I suddenly thought, why not a tube round the silicon........

 

[wild willy]

Thats a first class piece of engineering there. I think your talents are wasted. It looks a sturdy piece of kit, your on a winner with that design.
An interesting day for the silver machine tomorrow.

 

[DPJ]

Cheers Carl.

Fingers crossed the trimming goes right and it actually all fits.

 

[UncleFester]

Lots of custom work going on there, looks very smart ... does that bracket foul on the pipe or is it just the angle of the photo?

 

[DPJ]

Lots of custom work going on there, looks very smart ... does that bracket foul on the pipe or is it just the angle of the photo?

This one - the cable bracket at the left

No it's the angle of the photo.

 

[PhilW]

Lookin good fair play dave, bet its gonna be a complete arse to fit tho!

Good luck with it, hope it helps a lot.

 

[UncleFester]

This one - the cable bracket at the left

No it's the angle of the photo.

I don't know why i even thought it would - since you've spent the last few days looking at it

 

[DPJ]

I don't know why i even thought it would - since you've spent the last few days looking at it

No, I designed it, but I only picked it up at 7:00 tonight. Your questions are appreciated, Pat. It's surprising how one can look at something for ages and then completely miss the obvious.