induction kits, dump valves (yes again !)

[deano82]

Hi all,


On my LCR I have decided i'd like to hear more of a dump valve noise, I've got a forge 007p and i currently have a green cotton panel filter with a smoothed and drilled box and a 3" feed. I realise my dv isnt atmospheric but i have been told if i was to have an open cone filter then i would hear it and in fact it can still sound pretty loud from in and out the car, is that right ?
What kits would be best for this ?

I know there a loads od threads on this kinda subject but havnt found the exact answers im looking for and i like to make new posts

cheers

 

[marv_n69]

Keep the 007p mate and just get an open cone induction kit, piperx, k&n etc!!!

 

[s1l3nc3r]

If you want it louder than your current setup then an open filter will do that...if you want it louder than that still id recomend a turbosmart dualport.

 

[LEE69]

I'm trying an HKS filter on mine at the moment, and flip is it loud!

 

[danny20vt]

Remove the rug that's fitted to the underside of the bonnet, I've done this along with a green cone filter, a 007p with coldside kit and it sounds almost atmospheric also an LCR runs more boost so should be even louder.

 

[adam cupra 20vt]

I recently changed to open cone with the 007 and its pretty loud

 

[Willie]

http://cgi.ebay.co.uk/Saber-Fake-Du...s_SM?hash=item2303053c8e&_trksid=p3286.c0.m14
This sounds like it will fit your needs perfectly

 

[deano82]

I recently changed to open cone with the 007 and its pretty loud

What make open cone you got mate

 

[deano82]

I'm trying an HKS filter on mine at the moment, and flip is it loud!

Isnt HKS for Jap cars ? Which one fits then ?

 

[slim20vt]

http://cgi.ebay.co.uk/Saber-Fake-Du...s_SM?hash=item2303053c8e&_trksid=p3286.c0.m14
This sounds like it will fit your needs perfectly

you must be taking the mick

only a complete muppet would use on of these.. lol

go for the green filter cone 200mm 80mm inlet to maf fitment.. around £47

and remove your bonnet insulation, and remap it then you will be happy.. and loud i am with mine..

 

[Willie]

LOL
The Paxo sounds great with it though, lol

 

[LEE69]

Isnt HKS for Jap cars ? Which one fits then ?

80mm fits the LCR straight on, but i used 70mm pipe on my LC fits the MAF and pushes inside the neck of the filter very very snuggly.

 

[munkyboy]

I have a Carbonio Cold Air induction with a 007P and you cannot stop me from giggling. Im like a little kid when it comes to stupid DV noises. but Im hoping when I get it remapped it will be a bit louder again. But yeh definately I woudl go for an open cone to get a louder noise

 

[LEE69]

I agree I also like the noise too, some people do, some don't.

 

[adam cupra 20vt]

What make open cone you got mate

Its an Apexi filter down behind my bumper.

 

[marv_n69]

If i remove the soundproofing from under the bonnet will the heat from the engine damage the paint on the bonnet??????

 

[LEE69]

No, it will be fine.

 

[marv_n69]

Are you sure?

 

[LEE69]

See post 17

 

[slim20vt]

the heat from under the bonnet does not effect the paint in any way mine has been off for 14months i done 14k miles in all heat weather conditions............

it is only there for sound proofing FACT...............................