what have you done to your car today ?

[BenG]

Fitted 80mm silicone ducting into my airbox to replace the standard snorkel.

Adjusted cable tension of door handles as some were getting difficult to open.

Disconnected & plugged EGR vacuum hose. The engine light is on anyway so thought I'd try running without EGR for a while...

 

[8bit]

Sorted out the undertray fixings a bit better, it was sitting too low and catching on speed bumps after I changed the EGT sensor a couple of weeks ago. Also re-did the R badges again as the ones I put on earlier this year looked tatty really quick so used lacquer this time. Added an extra one for a couple more bhp

 

[LeonUser]

Giving back my mk2 leon to garage as a (rejected car) and going back to mk1 leon! until i can find something else to find....

 

[LunaR]

Refurbed/relacquerd my brembos

 

[Pete225]

Refurbed/relacquerd my brembos

Good job there mate

 

[Roach]

Wrung its neck like the cheap ***** it is!!

Anyone got a guide for refurbing the brembos? ^^^

 

[LEE69]

Search is ace

http://www.seatcupra.net/forums/showthread.php?t=122617&highlight=brembo+refurb

 

[Roach]

Yeah mine are a bit far gone for a coat of laquer.

I guess it's a caliper off job?

 

[03cupra]

spent today replacing an electrical connecter i managed to destroy drilling through the spare grommit to run to silicone hose for the boost gauge. Easy job, just a pain replacing the disconnector box in such a small space...

 

[LEE69]

Hope you re-sealed that box well, main area where water comes in the car

 

[03cupra]

Hope you re-sealed that box well, main area where water comes in the car

i did indeed Lee, used the remainder of the black silicone i had from resealing the doors... although i only touched the spare grommit i thought id do all of it given the proximity to the electrics there

 

[LunaR]

Thanks pete best £14 I've spent on the car. They were in abit of a state usual pink fade and lacquer peeling and bubbled up but I'm guessing it could've been worse lol.

 

[wazza5]

Fitted black headlining and trim. Adding to the armrest at the weekend. Hopefully get some pics up soon.

Sent from my GT-I8190N using Tapatalk 2

 

[x_jago_x]

Booked her in to AMD! .

 

[SLeon]

fitted new mats! looks loads smarter now

 

[Captain Cupra]

Something that's bugged me since forever, had the inner ends of the side skirts sprayed once before but already they are sandblasted by the road rash, to permanently sort this I did this

Here's the issue

So I cut some templates and transferred to 2mm abs sheet and cut these out

Used some oe screws

Eh viola!

Takes the eye of the unsightly rashing, plastic will wear bit not as visible and looks loads better, I think anyway , done this both side obviously

 

[joshy514]

Something that's bugged me since forever, had the inner ends of the side skirts sprayed once before but already they are sandblasted by the road rash, to permanently sort this I did this

Here's the issue

So I cut some templates and transferred to 2mm abs sheet and cut these out

Used some oe screws

Eh viola!

Takes the eye of the unsightly rashing, plastic will wear bit not as visible and looks loads better, I think anyway , done this both side obviously

Fancy making me some I hate mine for this!


Sent from my iPhone

 

[Pete225]

Something that's bugged me since forever, had the inner ends of the side skirts sprayed once before but already they are sandblasted by the road rash, to permanently sort this I did this

Here's the issue

So I cut some templates and transferred to 2mm abs sheet and cut these out

Used some oe screws

Eh viola!

Takes the eye of the unsightly rashing, plastic will wear bit not as visible and looks loads better, I think anyway , done this both side obviously

Cracking idea that!! My side skirts look very similar, the yellow is being chewed away by the roads and almost black :/ lol

 

[RaviR50]

good job dude great idea!

 

[Captain Cupra]

Fancy making me some I hate mine for this!


Sent from my iPhone

Can do, £20 posted? it is labour intensive about an hours work tbh and the abs plastics not cheap could have them on there way tomorrow?