what have you done to your car today ?

[Bouncerbeater]

Well, I have been over to Badger5 for a custom remap. Well pleased !

 

[lmiller]

Not sure. Just seem to boost as hard as standard air box. Possibly the noise making it feel like it should be faster than it sounds. Also the recirc into the box is a little chavvy for me. But we will see how it goes

I thought the same. Boggy down low with that filter on.

Sent from my GT-I9505 using Tapatalk

 

[bruceR]

Washed all the family cars: mine, the lasses & the young lads
Also received my new fan spray washer jets - to be fitted

 

[RaviR50]

Washed all the family cars: mine, the lasses & the young lads
Also received my new fan spray washer jets - to be fitted

what jets did you get?? i want some fans myself

 

[bendyb633]

Hit a pheasant in my car, smashed the front grill. GRRRRRR. If any one has or knows the part number for the lower centre section for it, please PM me. My car is a pre facelift Cupra on a 51 plate. Thanks.

 

[Kingscote]

Found my d/s door seal to be letting water in Anyone know how much they are fron the dealers? Or anyone on here sell them?

 

[useyourname]

Found my d/s door seal to be letting water in Anyone know how much they are fron the dealers? Or anyone on here sell them?

You can buy a roll of sticky sealant tubing stuff from ebay - no idea what's called . just cut to size, peel back to reveal stick layer and apply. i replaced all 4 seals when i got my car as they were leaking. takes about 25 mins per door. there's a guide on here somewhere.

 

[LEE69]

Found my d/s door seal to be letting water in Anyone know how much they are fron the dealers? Or anyone on here sell them?

http://www.seatcupra.net/forums/showthread.php?p=3255713#post3255713

 

[Kingscote]

Sorry chaps I mean the seal which is on the car not round the window regulator panel. Or does this allow water to go over?

 

[LEE69]

The actual door seal rarely fails

 

[LEE69]

Plenty of breakers about though if yours is damaged

 

[Kingscote]

I think I'll look at the regulator seal first as I have done this before. Thanks for the replys though

 

[bruceR]

what jets did you get?? i want some fans myself

Hi mate, they are off a Ford Focus. Fitted them 2day and they look OEM, however, the spray was a bit too high so had to pack the back of them with a piece of rubber grommet that came with them.

 

[mill5y]

]Got round to finishing fitment of front mount and forge map pipe after not knowing I needed one and blue petering a temp fix

Had a nightmare with it, but its done and holding 10-12psi fine.
So along with my 3" downpipe and 2.5 decat system am about ready for a remap..

Still a little bit more to take off inside of bumper, just dnt sit quite right,

 

[Peely]

Got my Brembo's on, fit snug under the 17" Rondals

 

[ezza24]

I thought you could use the original map sensor pipework ? Or is that only on the Lcr

 

[BoostHard]

Only lcr

Sent from my GT-I9300 using Tapatalk

 

[BoostHard]

Map sensor on k03 is in the top of the cooler

Sent from my GT-I9300 using Tapatalk

 

[ezza24]

Thought So as I am fitting my welly cooler at the weekend on my lcr seemed a good idea to check

 

[dave1221]

i fitted LCR alloys to my TDI Cupra and painted the calipers red:



a massive improvement