what have you done to your car today ?

[Ron Burgandy]

Fitted my coilovers

Driven a few miles and analy measured the height of each wheel arch and adjusted to suit... Nightmare all 4 wheels are now within 5 mm of each othet i can live with that!

measuring anything anally sounds painful. (Sorry couldn't resist)

 

[Brettyboy]

Had a busy day fitting

Eibach 25mm front arb

Polybushed wishbones & new ball joints

& gave it a oil,oil filter & diesel filter change

 

[Law121]

Changed oil and filter changed gearbox oil tyre pressures fitted a bov dumpvalve which was a fail

 

[dazjstuart]

Replaced my broken TCS button with a 2nd hand one off fleabay. Got a new wheel speed sensor too fitting it tomorrow, hopefully that will sort the ABS out!

 

[MarkWales]

Here is the picture of the rear drop

and before

 

[The crow]

aluminium floor mat protector

forge silicone couple

 

[Mk1 banana]

Cleared the sai fault code, again, despite having fitted 330 ohm, 10 watt resistors for my n112/249 delete?

And established a boost leak, 90 degree hose under Inlet mani... Perhaps that's why she peaks at 1.4 bar then drops to 0.7 bar again.

 

[Guizado]

Fitted a JR Filter, Serviced my 007p, changed my battery, fitted some leds to the low beams enabled auto-windows and fixed my rear washer which had a loose pipe just behind the Cigarrete lighter thing on the boot.

 

[beastgtir]

Fitted my new Cupra mats. Gave it a wash and clean, in preparation for a wax tomorrow.

 

[RaviR50]

yesterday, gave it a quick machine polish and a wax looked really good. pics in a bit.

also got some smoked side repeaters, auto art ones they said it was for 99-05 leon but the bulb holders didnt fit in?? anyone had experience with that??

 

[RICKY3]

yesterday, gave it a quick machine polish and a wax looked really good. pics in a bit.

also got some smoked side repeaters, auto art ones they said it was for 99-05 leon but the bulb holders didnt fit in?? anyone had experience with that??

Are your holders too big or too small?


Sent from my iPhone

 

[RaviR50]

Are your holders too big or too small?

too big, i broke one of the repeaters thinking its surely gotta go in

 

[RICKY3]

Can you drill out the twist fitting and use the rubber boot to hold them in?


Sent from my iPhone

 

[Crhome]

Stage 1 remap yesterday at AMD, and drove away with a massive smile on my face Then I went out and burned some V Power around Hertfodrshire.

 

[Murdered LCR]

was yesterday but sorted my car out with ride hight not 100% happy so orderd camber top mounts washed the car as well

These to bring the front in and down

 

[RaviR50]

Can you drill out the twist fitting and use the rubber boot to hold them in?

uumm yeah guess i could do but then would they really be secure??

 

[LEE69]

yesterday, gave it a quick machine polish and a wax looked really good. pics in a bit.

also got some smoked side repeaters, auto art ones they said it was for 99-05 leon but the bulb holders didnt fit in?? anyone had experience with that??

early and late ones have different bulb holders

 

[RICKY3]

uumm yeah guess i could do but then would they really be secure??

Once the boot is on cable tie it


Sent from my iPhone

 

[RaviR50]

Once the boot is on cable tie it

sorry, dont quite get what you mean mate

 

[RICKY3]

My bulb holders have a rubber boot around them once bulbholder is in boot goes over the lamp base and cable tie round boot to hold it to holder


Sent from my iPhone