DaNnY_LaD's HTA-Gt2868R Big turbo Build(Now @ AKS Tuning)

[RS6]

all this money spent danny just take it to a vag specialist for them to have a look it won't be much i bet but least you have piece of mind its setup right

 

[james.l]

If it helps I can send you a copy of the timing images from ELSAWIN?

IIRC it's 16 rollers between the cams

 

[DaNnY_LaD]

It'd been built by a vag specialist so there's no need . My mate will check the timing when he comes todo the vvt gasket.

Please James send it over ;-)

Yeah please phil we have had te cams out as the head has been fully rebuilt along with the bottom end ..funny think is it starts first time lol..

Can anyone run me through how todo the tba

 

[james.l]

It'd been built by a vag specialist so there's no need . My mate will check the timing when he comes todo the vvt gasket.

Please James send it over ;-)

will get it over this eve

 

[-pseudonymous-]

Can anyone run me through how todo the tba

http://www.ross-tech.com/vag-com/cars/throttlebody.html

Remember to do it with a cold engine.

 

[JordanMk3]

http://www.ross-tech.com/vag-com/cars/throttlebody.html

Remember to do it with a cold engine.

Cant get a better quide than that!!

Hope you get it sorted out soon Danny... When you thinking of MOTing and TAXing her?

 

[PhilW]

It'd been built by a vag specialist so there's no need . My mate will check the timing when he comes todo the vvt gasket.

Please James send it over ;-)

Yeah please phil we have had te cams out as the head has been fully rebuilt along with the bottom end ..funny think is it starts first time lol..

Can anyone run me through how todo the tba

Quick question, are you using your original cam cover?

It's easy to do tho.

Start with the cambelt, set it to tdc using the crank pulley notch.. This one is out slightly..

Then check your marks on the cam against the cam cover notch.

If that's ok your cam to cam timing.

If either are out you'll throw a code but it doesn't really make much starting differenc but just feels a bit down on power that's all.

 

[DaNnY_LaD]

Thanks Phil,,

Im doing a TBA now with that guide but its sayin error in the top right box with these codes

VAG-COM Version: Release 311.2-N

Control Module Part Number: 1ML 906 032 A
Component and/or Version: 1.8l R4/5VT 0001
Software Coding: 10510
Work Shop Code: WSC 77875
Additional Info: VSSZZZ1MZ3R056288 SEZ7Z0B1737303
5 Faults Found:
17987 - Throttle Actuator (J338): Adaptation Not Started
P1579 - 35-00 - -
17695 - Boost Pressure Control Valve (N249): Open Circuit
P1287 - 35-00 - -
17748 - Camshaft Position Sensor (G40) / Engine Speed Sensor (G28): Incor. Correlation
P1340 - 35-00 - -
17951 - Angle Sensor 1 for Throttle Actuator (G187): Signal too Small
P1543 - 35-00 - -
17580 - Angle Sensor 2 for Throttle Actuator (G188) Signal too Low
P1172 - 35-00 - -

 

[DaNnY_LaD]

Had a awesome Day today Managed to sort all the Hosing and vac piping out,Renew all my Clamps and clips And re done my exhaust and it no long has a slight Hiss coming from it Result...

Also big thanks to chris whitworth for todays antics Was a massive help he got my TB all Done TBA and it idles a real Treat ....slight cough 3-4 secs after starting it then its fine...

Just These 2 codes to sort now and its all done..
17695 - Boost Pressure Control Valve (N249): Open Circuit
P1287 - 35-00 - -
17748 - Camshaft Position Sensor (G40) / Engine Speed Sensor (G28): Incor. Correlation
P1340 - 35-00 - -

 

[PhilW]

Your timing is out. Without a doubt.

 

[DaNnY_LaD]

Thanks phil..out of interest can it be test with vag com to see if it's out?

 

[James.Judd.1]

Danny just look at the timing marks LOL!!!!!!!! Stop being lazy

 

[DaNnY_LaD]

That will have to wait now lol...Dnt have time to strip it down

 

[James.Judd.1]

Strip what down?

 

[DaNnY_LaD]

Am i right in thinking that the Front Discs on the LCR brembos Are 323mm x 28mm by 5 x112? And the Brakes on the AUDI s4 2.7t is 323mm and 5x 112?

 

[m0rk]

Your PCD is 5x100 for starters

 

[DaNnY_LaD]

Your PCD is 5x100 for starters

Thanks Mork..

 

[DaNnY_LaD]

Just Sorting My Brake Setup now as my current one will Not pass a MOT so Going for the GODspeed 323mm X 28mm Ones With 6 grooved centres..

 

[chris_200120vt]

Had a awesome Day today Managed to sort all the Hosing and vac piping out,Renew all my Clamps and clips And re done my exhaust and it no long has a slight Hiss coming from it Result...

you know you want a liquid gauge now , want a drive in it though

 

[James23Parkin]

You're sounding more confident and comfortable with the engine now that you're getting on top of the list of jobs Danny. I've really enjoyed following your progress over the last few weeks.

I hope it beds in well so that you can enjoy driving it again

The Godspeed discs are highly regarded... Did you go for the single piece or 2 piece discs? Either way they'll look nice nice behind the wheels... and should work well too.

James