its saves you £70 thats why. it doesn't bother me having something like fitted to my car, its pretty much the same as the home made cai and drestricted airbox i have fitted - i'd rather not spend £150 on a BMC so i did that instead. Its a bit DIY but its hardly a bodge or anything like that.
-
Guest, New Stock alert: Premium CUPRA valve caps now available in the store ? Order now from the merchandise store
My DIY Short Shifter
- Thread starter xd-data-ii
- Start date
If something can be modified yourself then why not try it. I didnt think it was worth paying over €70 (plus shipping) without trying it myself.
There is no structural problems with drilling into the cast iron shifter.
Looks like there is a lot who would want this. I will see what i can do and what time i have.
If figured just creating the pin was neccesary but maybe the drilling and tapping the shifter after might not be a job for everyone.
There is no structural problems with drilling into the cast iron shifter.
Looks like there is a lot who would want this. I will see what i can do and what time i have.
If figured just creating the pin was neccesary but maybe the drilling and tapping the shifter after might not be a job for everyone.
Last edited:
Does it have to be tapped?. Can a nut not be used on the other side or is there no clearence?. All we have to do is drill the holes ourselves and purchase a pin
That would work too I suppose
I tapped it to be sure but i suppose it doesnt really need to be.
Use a nylon locking nut underneath - there is enough clearance.
I tapped it to be sure but i suppose it doesnt really need to be.
Use a nylon locking nut underneath - there is enough clearance.
I don't like the idea of the flex that might produce, it's much better to tap the hole and have it fitted securely so that it can't move around.
Why get a second hand one?
As a test to see if you can do it properly? Maybe yes.
But just modify the original otherwise.
Oh and tapping the hole will make the shifter more rigid and make the bolt/pin part of the shifter so is best to do this if you can.
As a test to see if you can do it properly? Maybe yes.
But just modify the original otherwise.
Oh and tapping the hole will make the shifter more rigid and make the bolt/pin part of the shifter so is best to do this if you can.
You didn't happen to make a drawing of the pin when you were turning it did you?
If not I'll draw it in Pro/E when I've got the shifter off to do this on my 1.6 and post the PDF here.
If not I'll draw it in Pro/E when I've got the shifter off to do this on my 1.6 and post the PDF here.
I took dimensions and made hand drawings of each section of the pin required to make it.
I'll try route it out and let you know
I'll try route it out and let you know
the one in the pictures?
Its the new created one. The original never left the shifter.
It was created using measurements based on the original.
Its the new created one. The original never left the shifter.
It was created using measurements based on the original.
i'll be taking mine off tomorrow night and making a pin on tuesday at work i think. an hours work and £150 to spend on something worthy of that sort of money. well done mate. i'll try and make a drawing of the pin and put it on here for everyone else who is able to make one.
As said, tapping the shifter would be the best solution.
Regards the comments re the PLI, of course if someone does a bad job that's a problem but what's proposed is not rocket science.
We have become too litigious as a society, and our fear to try things (and on the grand scale this isn't a risky job) and the lack of core engineering skills is actually inhibiting creativity in this country.
Regards the comments re the PLI, of course if someone does a bad job that's a problem but what's proposed is not rocket science.
We have become too litigious as a society, and our fear to try things (and on the grand scale this isn't a risky job) and the lack of core engineering skills is actually inhibiting creativity in this country.
Similar threads
