-
Guest, 🚨New Stock alert: Premium CUPRA valve caps now available in the store 👉 Order now from the merchandise store
what have you done to your car today ?
- Thread starter seatcupramad23
- Start date
had a go and fixing the good old leaking doors, most likerly made them worse...
changed my fog light bulb. while changing it I noticed the SMIC, so drilled a few holes in the foglight support in the bumper to try and increase airflow.
apart from wheel arch mod , and removing fog light completely any other ways to increase airflow to the SMIC ?
changed my fog light bulb. while changing it I noticed the SMIC, so drilled a few holes in the foglight support in the bumper to try and increase airflow.
apart from wheel arch mod , and removing fog light completely any other ways to increase airflow to the SMIC ?
Last edited:
Found a split pipe
this is under the inlet manifold
can any one tell me if its vacuum or breather ?
this is under the inlet manifold
can any one tell me if its vacuum or breather ?
Last edited:
Finally refitted the engine after six months so back up and running only to find out that I now have an oil leak of the crank oil seal. Ho well looks like gearbox out now then
Hear a picture of my new BMC Induction kit plus my new rim blades, I do have to say my cars looking very nice, also what a massive difference changing from the K&N 57i filter, the car is soooo quick now it's unreal, this induction kit is a must if u have a spare £180 lol
Last edited:
Leon Cupra R mods fitted!
I'm so lucky to have this car, in 2005 I purchased the very last BAM 225 Leon off the production line in Spain, brought down to me from Barcelona. After over 10 years the clutch began to slip, I already had a few light mods done, d/v, BMC CDA and a remap, but this evening I just finished fitting a few mods over here in sunny Gibraltar. Mods such as: FMIC (Airtech), Tarox F2000's brakes front & rear, Tarox Strada pads front & rear. Upgraded the Milltek catback into a turbo back system with the large-bore downpipe and catalyst bypass assembly. Installed the complete Sachs SMF motor-sports kit, disc, pressure plate, lightened flywheel and uprated slave cylinder. Oh and a Quaife LSD!
Just got back home an hour ago, so have been gentle Next week, I will be hooking up my PLX kiwi 2 device to the OBD2 port and start logging some data! I am still waiting to sort out the braided brake lines, but the ones I receives had those banjo fittings and I received no bolts to adapt them for a good fit, so I'm in the process of having them replaced. Also, I need to replace my large TIP because yes, as it’s a left-hand drive car the larger TIP is hitting the brake master cylinder and causing some rubbing against the silicone of the TIP (I fear soon it will breach and cause a slight leak which will obviously not be good), so that will be replaced for a more adequately sized one. Also will be replacing the upper inter-cooler hoses, charge pipe, and d/v cold-side kit is also still to arrive and be fitted. Pictures were with my old phone, so apologies for the bad quality, but I'm also finding it difficult to attach the images to this message, so the images might not even be here! Anyway, I'm exhausted from working all day, so will try to add them again if not successful, at some stage tomorrow. . . (Im looking at the preview and still cant see my images or attach them, sorry I'm a rare forum poster so am a complete novice at attaching images for this arrgghh! lol. Nite nite.
I'm so lucky to have this car, in 2005 I purchased the very last BAM 225 Leon off the production line in Spain, brought down to me from Barcelona. After over 10 years the clutch began to slip, I already had a few light mods done, d/v, BMC CDA and a remap, but this evening I just finished fitting a few mods over here in sunny Gibraltar. Mods such as: FMIC (Airtech), Tarox F2000's brakes front & rear, Tarox Strada pads front & rear. Upgraded the Milltek catback into a turbo back system with the large-bore downpipe and catalyst bypass assembly. Installed the complete Sachs SMF motor-sports kit, disc, pressure plate, lightened flywheel and uprated slave cylinder. Oh and a Quaife LSD!
Just got back home an hour ago, so have been gentle Next week, I will be hooking up my PLX kiwi 2 device to the OBD2 port and start logging some data! I am still waiting to sort out the braided brake lines, but the ones I receives had those banjo fittings and I received no bolts to adapt them for a good fit, so I'm in the process of having them replaced. Also, I need to replace my large TIP because yes, as it’s a left-hand drive car the larger TIP is hitting the brake master cylinder and causing some rubbing against the silicone of the TIP (I fear soon it will breach and cause a slight leak which will obviously not be good), so that will be replaced for a more adequately sized one. Also will be replacing the upper inter-cooler hoses, charge pipe, and d/v cold-side kit is also still to arrive and be fitted. Pictures were with my old phone, so apologies for the bad quality, but I'm also finding it difficult to attach the images to this message, so the images might not even be here! Anyway, I'm exhausted from working all day, so will try to add them again if not successful, at some stage tomorrow. . . (Im looking at the preview and still cant see my images or attach them, sorry I'm a rare forum poster so am a complete novice at attaching images for this arrgghh! lol. Nite nite.
I'm so lucky to have this car, in 2005 I purchased the very last BAM 225 Leon off the production line in Spain, brought down to me from Barcelona. After over 10 years the clutch began to slip, I already had a few light mods done, d/v, BMC CDA and a remap, but this evening I just finished fitting a few mods over here in sunny Gibraltar. Mods such as: FMIC (Airtech), Tarox F2000's brakes front & rear, Tarox Strada pads front & rear. Upgraded the Milltek catback into a turbo back system with the large-bore downpipe and catalyst bypass assembly. Installed the complete Sachs SMF motor-sports kit, disc, pressure plate, lightened flywheel and uprated slave cylinder. Oh and a Quaife LSD!
To get ur pictures up go on photo bucket upload ur pictures then copy the IMG link on the right then past it into ur message
Last edited:
Asfaik you can achieve 180bhp with just a remap on these so you should be looking at upward of that
Sent from my GT-I9195 using Tapatalk
Fidge it's a 1.9 tdi 8v engine code asv they Are 110bhp standard mate a remap your looking at 140-145 @ stage 1 I think you may be confusing it with the 2.0 tdi engine which is 140bhp standard and can be tuned to 180bhp with a stage 1
Seat Leon 1.9tdi 110bhp ASV, BMC CDA,Egr delete, decat,
Ah confusing it with the 1.9 PD, shameFidge it's a 1.9 tdi 8v engine code asv they Are 110bhp standard mate a remap your looking at 140-145 @ stage 1 I think you may be confusing it with the 2.0 tdi engine which is 140bhp standard and can be tuned to 180bhp with a stage 1
Seat Leon 1.9tdi 110bhp ASV, BMC CDA,Egr delete, decat,
Sent from my GT-I9195 using Tapatalk
Which 1.9 PD? There a several lol mine is ve not pd
Seat Leon 1.9tdi 110bhp ASV, BMC CDA,Egr delete, decat,
Seat Leon 1.9tdi 110bhp ASV, BMC CDA,Egr delete, decat,
Any of the 1.9 PD they have better potential for remaps where 90/ 110/ 130 or 150 stock
Sent from my GT-I9195 using Tapatalk
Fitted a new 710p replaced the old 710p and fitted it the correct way round as PO had it backwards and poly bushed the dog bone, made a great difference to the feel, I think it's got the wrong bolt in it though as I had nearly 10mm of slack on the bolt before it even started clamping the bushes, I haven't suffered no extra vibration though and axel tramp has disappeared
Run engine flush, dropped oil and filter, dropped sump and cleaned, removed and cleaned oil pick up pipe, refitted and refilled with oil, then looked at me new injectors and thought "nah sod it I'll do em Monday" lol
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Similar threads
