identification

  1. Part Identification

    I have a 2004 seat Leon 150 tdi cupra. On the back fire wall in between the two pressure converters for the boost and the egr there is another unit. It has a silver top on with made in USA and has the following part number 1J0906283C. Does anyone know what this part is? Is it something to do...
  2. Cambelt Identification

    Hey, just a quick one as a while of searching wasn't really giving me the answer i needed. It's a bit of an amateur question, but does anyone have a picture that clearly identifies where my cambelt is on a 1.4 mk1 leon? Is the belt that is clearly the visible the auxillary belt or the...
  3. LUK/Sachs flywheel identification

    For anyone with a Mk2 Leon, Mk3 Toledo or Altea TDI - If you ever need a flywheel, you need to know which make is fitted to your car. There is an inspection aperture in the bellhousing and if you rotate the crank you will see one of the setups below. The top one is LUK with parallel grooves The...
  4. lever identification required .. help please

    hya peeps, me again, i have a dseat ibiza 1995 diesel. at the side of the steering column is a lever. can someone tell me if this is a manual choke? i need to replace it and don't know what the name is of that part. thanks in advance, liza 283
  5. Rocky Rocastle

    Part no' identification and ARB bush question

    I while back i had an issue with a noise after lowering and I was asked by a member a number of questions on parts I replaced etc when the new suspension setup was added. One of the questions was: "were the 2 bolts in the wheel bearing housing replaced for new?" I need to explain to the...
  6. LC - Engine Bay - Parts Identification

    Here is my engine bay from my Cupra 180 AUQ. It's all stock except for the 007P and green cotton air filter which previous owner put in. I would really appreciate it if one or some of you could put me out of my misery and help me identify the parts, hoses/pipes and which can be replaced with...
  7. Help with Part Identification please

    Hi, trying to find reason for an error code on the car'17964' boost pressure negative deviation. anyhow i was tryin to identify problems with any hoses for the turbo(not that i've identified it) and found a partially cut/eroded hose connected to a black box on the drivers side of the...
  8. Help Please - LC part identification

    Hiya, Is there any chance that someone could identify this part for me please? This photo is taken from the position of the air box pointing towards the side of the head. This second photo is slightly enlarged. There is air escaping in the direction of the arrow. I can't find any...
  9. truss

    Pipe identification help please!

    Being the n00b i am, can anyone tell me what pipe ive arrowed is please?! i want to try and brighten up the engine bay as you can see by the pic. (i have now done the bypass stuff now aswell) If anyone knows the size etc too that'd be a help! Cheers...
  10. Tdi 110 toledo- part identification needed

    there is a part in my engine bay which is rattling. when looking into the cars engine from the front of car, it is a black tube, possible spring loaded, which is down beside the timing belt. is it a tensioner for the fan belt, and should it be rattling
  11. OFI

    Coil Spring Identification for 2001 Cupra

    Right so i've done a little search and come up with: http://www.seatcupra.net/forums/showthread.php?t=184973&highlight=spring http://www.seatcupra.net/forums/showthread.php?t=152027&highlight=spring and http://www.seatcupra.net/forums/showthread.php?t=100589&highlight=spring...
  12. Engine loom connector identification. Leon 1.8T AUQ

    Hi guys. I've started the conversion to the afternmarket ECU. But I'm stuck on the identity of one of the connectors. It is the only one that has a siver rubber cover. It is near the speed sensor. And pin colours are :Purple/White, Brown, Yellow/Black. It's don't seem to be in the...
  13. Engine loom connector identification. Leon 1.8T

    Hi guys. I've started the conversion to the afternmarket ECU. But I'm stuck on the identity of one of the connectors. It is the only one that has a siver rubber cover. It is near the speed sensor. And pin colours are :Purple/White, Brown, Yellow/Black. I'm thinking it's Reverse...
  14. PART Identification help please

    This was supplied to me by AUTOBITS who assured me it was the correct cat converter to fit my 1997 SEAT Ibiza Cupra Sport GTi 2.0 8v AGG engine type car - the fitting MOT+Repairs station said rubbish, it's not nearly right and I saw for myself that there was NO WAY it was right for this car...
  15. tackleberry

    wheel identification

    hi peeps, can anybody if possible please identify these wheels for me. 1 needs replacing and the insurance company need to know where they can get one from
Adrian Flux insurance services - discount for forum members.