MK3 Ibiza Cupra* K03s Jabbasport* Moving on....

[Berg]

Just ordered some led numberplate bulbs and interior bulb

Also on the hunt for some brakes now, think im going to get some cupra R brembos when funds allow.

I have also found the wheels ill be getting soon

Not much will be happening till after new year now though, just going to enjoy driving it for a while

 

[joehirth]

Just ordered some led numberplate bulbs and interior bulb

Also on the hunt for some brakes now, think im going to get some cupra R brembos when funds allow.

I have also found the wheels ill be getting soon

Not much will be happening till after new year now though, just going to enjoy driving it for a while

I like Cupra R front brakes ) BEWARE though (if you haven't already) braided lines and possible brake pipe maybe needed as they seize very well and the 90deg union snaps when you go to undo the caliper

 

[mini_hammy]

what is the chatter like from changing to a single mass from the dual mass??

 

[Berg]

I like Cupra R front brakes ) BEWARE though (if you haven't already) braided lines and possible brake pipe maybe needed as they seize very well and the 90deg union snaps when you go to undo the caliper

Hmm sounds interesting lol nothings ever simple lol

I had a look at the 312mm off the S3 etc but would rather something which is a straight swap and not have to get re-drilled discs etc

what is the chatter like from changing to a single mass from the dual mass??

Chatter??

I read up that there is suppose to be a noise on idle when using the solid flywheel but i dont have any noises what so ever

 

[Berg]

Heres the condition of the old dual mass flywheel

Seems to be some sort of contamination which doesnt look good.

I think this was as good as knackered too tbh

 

[Berg]

Heres the first of a couple of carbon touches.

Took a ladys touch to do this as i knew id mess it up lol!

Ill ad a pic of it fitted tomorrow

Also going to do inside the clocks/dials too

 

[ASHL3Y]

Badge looks sweet mate

 

[Berg]

Cheers mate

Going to laquer it tomorrow and job done!

 

[chris_200120vt]

take it is vinyl berg?

 

[Berg]

Yer it is mate

Its the proper Di-Noc stuff, just a bit dull so im gonna laquer it to make it shine better

 

[chris_200120vt]

did mine with the same stuff about 4 months ago would not bother putting laquer on it just spray some silicone spray on it. but i have to say the badges do look sweet in carbon so im going to be taking the vinyl off and doing it in the real stuff hope your going to do the rear badge as well

 

[Berg]

did mine with the same stuff about 4 months ago would not bother putting laquer on it just spray some silicone spray on it. but i have to say the badges do look sweet in carbon so im going to be taking the vinyl off and doing it in the real stuff hope your going to do the rear badge as well

Im not sure about the rear badge lol

Gonna do a photoshop and see what it looks like first

 

[chris_200120vt]

 

[tarzan]

Nice with the carbon.And good to see that shes back on the road with new clutch setup.

 

[Berg]

Hmm might have to do the rear badge after all

Nice with the carbon.And good to see that shes back on the road with new clutch setup.

Cheers mate

All running well without problems so far

 

[Berg]

Pic of the badge on the car

Also changed a few pipes again lol, had a couple of black sat around so decided to fit them, imo looks better than it did before although i wasnt happy with the other setup really as the old T-piece was 63mm so didnt like how it fitted the throttle body really and it sat against the fan motor before, alot of clearance now

 

[joehirth]

Heres the first of a couple of carbon touches.

Took a ladys touch to do this as i knew id mess it up lol!

Ill ad a pic of it fitted tomorrow

Also going to do inside the clocks/dials too

Ladies touch lol haha love that - looks smart though...

 

[Jdizzy]

Cars looking good berg

If u still have the coldside relocation at the end of the month I'll have a drive up to you and collect if that's ok?

 

[nat85]

nice car berg! good bhp and torque too. is there a part number or what do i ask for to get the same clutch/flywheel kit as you? cheers

 

[Berg]

Ladies touch lol haha love that - looks smart though...

Cheers mate, ha not something i could do neatly enough lol

Cars looking good berg

If u still have the coldside relocation at the end of the month I'll have a drive up to you and collect if that's ok?

Cheers mate, its in bits now though and will need some alloy pipe too in correct size as i used it on my new bits, let me know though i can link you to what you need and could fit it too if u dont know how to do it.

nice car berg! good bhp and torque too. is there a part number or what do i ask for to get the same clutch/flywheel kit as you? cheers

Cheers mate, if you go on euro car parts and put in your reg its under solid flywheel conversions, the valeo kit